! Proposal 6903, submission 1 ! PI: Baggett, Sylvia ! Received Fri Mar 22 15:19:23 EST 1996 ! From: shireen@stsci.edu !6903 Proposal_Information Title: WFPC2 CYCLE 6 CAL: DECON Proposal_Category: CAL/WF2 Scientific_Category: Cycle: 6 Investigators PI_name: Baggett, Sylvia PI_Institution: STSCI CoI_Name: Casertano, Stefano CoI_Institution: STSCI Contact: Y Abstract: This proposal defines the decontamination procedure to be run during cycle 5. A variety of internal images are taken before and after the decontamination in order to verify its success. Questions Observing_Description: Before and after each decontamination, a set of internals are taken: 2 biases (gain 7), 2 biases (gain 15), 2 F555W intflats (10S at gain 7), 2 F555W intflats (20S at gain 15), 2 kspots (one at 1.0 S, one at 2.6 S, both gain 15), and finally, 5 darks (gain 7, serials=off). Intflats must be taken without interruption; each set of internals should be grouped within two days. Decontamination procedure is performed 33H +/- 12H after first set of internals; final set of internals is done 12H +/- 12H after decon. IMPORTANT SCHEDULING NOTES: 1) Please do the internals as close as possible before and after a decon. 2) The DARKS in each visit should be done within 2 days. 3) PLEASE DO NOT INTERSPERSE OTHER WFPC2 SCIENCE OBSERVATIONS IN-BETWEEN THE FIVE DARKS IN EACH VISIT. THIS IS ESPECIALLY IMPORTANT FOR PRE-DECON EXPOSURES. We are worried about residuals from bright targets appearing in the darks. Visits !---decon cycle 1----------------------------------------------------------------------- Visit_Number: 01 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 1,2,3 is decon cycle #1. Visit 1 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 02 Visit_Requirements: AFTER 01 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 1,2,3 is decon cycle #1. Visit 2 does decon #1. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 03 Visit_Requirements: AFTER 02 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 1,2,3 is decon cycle #1. Visit 3 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 2----------------------------------------------------------------------- Visit_Number: 04 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 4,5,6 is decon cycle #2. Visit 4 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 05 Visit_Requirements: AFTER 04 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 4,5,6 is decon cycle #2. Visit 5 does decon #2. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 06 Visit_Requirements: AFTER 05 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 4,5,6 is decon cycle #2. Visit 6 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 3----------------------------------------------------------------------- Visit_Number: 07 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 7,8,9 is decon cycle #3. Visit 7 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 08 Visit_Requirements: AFTER 07 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 7,8,9 is decon cycle #3. Visit 8 does decon #3. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 09 Visit_Requirements: AFTER 08 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 7,8,9 is decon cycle #3. Visit 9 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 4----------------------------------------------------------------------- Visit_Number: 10 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 10,11,12 is decon cycle #4. Visit 10 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 11 Visit_Requirements: AFTER 10 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 10,11,12 is decon cycle #4. Visit 11 does decon #4 Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 12 Visit_Requirements: AFTER 11 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 10,11,12 is decon cycle #4. Visit 12 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 5----------------------------------------------------------------------- Visit_Number: 13 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 13,14,15 is decon cycle #5. Visit 13 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 14 Visit_Requirements: AFTER 13 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 13,14,15 is decon cycle #5. Visit 14 does decon #5. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 15 Visit_Requirements: AFTER 14 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 13,14,15 is decon cycle #5. Visit 15 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 6----------------------------------------------------------------------- Visit_Number: 16 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 16,17,18 is decon cycle #6. Visit 16 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 17 Visit_Requirements: AFTER 16 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 16,17,18 is decon cycle #6. Visit 17 does decon #6. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 18 Visit_Requirements: AFTER 17 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 16,17,18 is decon cycle #6. Visit 18 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 7----------------------------------------------------------------------- Visit_Number: 19 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 19,20,21 is decon cycle #7. Visit 19 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 20 Visit_Requirements: AFTER 19 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 19,20,21 is decon cycle #7. Visit 20 does decon #7. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 21 Visit_Requirements: AFTER 20 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 19,20,21 is decon cycle #7. Visit 21 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 8----------------------------------------------------------------------- Visit_Number: 22 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 22,23,24 is decon cycle #8. Visit 22 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 23 Visit_Requirements: AFTER 22 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 22,23,24 is decon cycle #8. Visit 23 does decon #8. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 24 Visit_Requirements: AFTER 23 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 22,23,24 is decon cycle #8. Visit 24 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 9----------------------------------------------------------------------- Visit_Number: 25 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 25,26,27 is decon cycle #9. Visit 25 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 26 Visit_Requirements: AFTER 25 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 25,26,27 is decon cycle #9. Visit 26 does decon #9. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 27 Visit_Requirements: AFTER 26 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 25,26,27 is decon cycle #9. Visit 27 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 10---------------------------------------------------------------------- Visit_Number: 28 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 28,29,30 is decon cycle #10. Visit 28 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 29 Visit_Requirements: AFTER 28 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 28,29,30 is decon cycle #10. Visit 29 does decon #10. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 30 Visit_Requirements: AFTER 29 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 28,29,30 is decon cycle #10. Visit 30 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 11----------------------------------------------------------------------- Visit_Number: 31 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 31,32,33 is decon cycle #11. Visit 31 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 32 Visit_Requirements: AFTER 31 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 31,32,33 is decon cycle #11. Visit 32 does decon #11. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 33 Visit_Requirements: AFTER 32 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 31,32,33 is decon cycle #11. Visit 33 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 12----------------------------------------------------------------------- Visit_Number: 34 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 34,35,36 is decon cycle #12. Visit 34 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 35 Visit_Requirements: AFTER 34 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 34,35,36 is decon cycle #12. Visit 35 does decon #12. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 36 Visit_Requirements: AFTER 35 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 34,35,36 is decon cycle #12. Visit 36 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 13----------------------------------------------------------------------- Visit_Number: 37 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 37,38,39 is decon cycle #13. Visit 37 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 38 Visit_Requirements: AFTER 37 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 37,38,39 is decon cycle #13. Visit 38 does decon #13. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 39 Visit_Requirements: AFTER 38 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 37,38,39 is decon cycle #13. Visit 39 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 14----------------------------------------------------------------------- Visit_Number: 40 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 40,41,42 is decon cycle #14. Visit 40 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 41 Visit_Requirements: AFTER 40 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 40,41,42 is decon cycle #14. Visit 41 does decon #14. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 42 Visit_Requirements: AFTER 41 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 40,41,42 is decon cycle #14. Visit 42 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !---decon cycle 15----------------------------------------------------------------------- Visit_Number: 43 Visit_Requirements: On_Hold_Comments: Visit_Comments: Visits 43,44,45 is decon cycle #15. Visit 43 does pre-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- Visit_Number: 44 Visit_Requirements: AFTER 43 BY 0H TO 18H On_Hold_Comments: Visit_Comments: Visits 43,44,45 is decon cycle #15. Visit 44 does decon #15. Exposure_number: 10 Target_Name: DARK Config: WFPC2 Opmode: DECON Aperture: WFALL Sp_Element: ! must leave blank; using 'DEF': SYNTAX: DEF not available for WFPC2 & DECON. ! "Please check the Phase II Proposal Instructions ! leaving blank: get feasibility error as opposed to syntax Wavelength: Optional_Parameters: Number_of_iterations:1 Time_Per_Exposure: 0.0S Special_Requirements: Comments: QASISTATE: WFII SI DECON Visit_Number: 45 Visit_Requirements: AFTER 44 BY 0H TO 24H On_Hold_Comments: Visit_Comments: Visits 43,44,45 is decon cycle #15. Visit 45 does post-decon internals. Execute as close to decontamination as possible. Five darks should be done within 2 days. PLEASE DO NOT SCHEDULE ANY WFPC2 SCIENCE EXPOSURES IN-BETWEEN THE DARKS. Exposure_number: 1 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 2 Target_Name: BIAS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:2 Time_Per_Exposure: 0S Special_Requirements: Comments: Exposure_number: 10 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements: Comments: Exposure_number: 20 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 10S Special_Requirements:SEQ 10-20 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 30 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements: Comments: Exposure_number: 40 Target_Name: INTFLAT Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: F555W Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 20S Special_Requirements:SEQ 30-40 NON-INT Comments: DO INTFLATS BACK-TO-BACK Exposure_number: 50 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 1S Special_Requirements: Comments: Exposure_number: 60 Target_Name: KSPOTS Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: ATD-GAIN=15 Number_of_iterations:1 Time_Per_Exposure: 2.6S Special_Requirements:SEQ 50-60 NON-INT Comments: DO KSPOTS BACK-TO-BACK !darks----- Exposure_number: 71 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times--All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 72 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 73 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 74 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. Exposure_number: 75 Target_Name: DARK Config: WFPC2 Opmode: IMAGE Aperture: WFALL Sp_Element: DEF Wavelength: Optional_Parameters: CR-SPLIT=NO, CLOCKS=NO, ATD-GAIN=7 Number_of_iterations:1 Time_Per_Exposure: 30M Special_Requirements: Comments: RPS2 is changing exposure times. All DARKS must be 1800s! Do all five darks within 2 days. Don't schedule wfpc2 science exposures in-between darks. !darks----- !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Data_Distribution Medium: 8MM Blocking_Factor: 10 Ship_To: BAGGETT Ship_Via: UPS Recipient_Email: