coverpage: title_1: FOC/48 LONG SLIT APERTURE LOCATION proposal_for: CAL/FOC pi_title: DR. pi_fname: ANTONELLA pi_lname: NOTA pi_inst: SPACE TELESCOPE SCIENCE INSTITUTE pi_country: USA foc: X ! end of coverpage abstract: line_1: The aim of these observations is to determine the Post-COSTAR line_2: position of the F/48 slit for long-slit spectroscopic line_3: observations. ! ! end of abstract general_form_proposers: lname: NOTA fname: A. title: DR. inst: SPACE TELESCOPE SCIENCE INSTITUTE country: USA ! ! end of general_form_proposers block general_form_text: question: 3 section: 1 line_1: This proposal will attempt to locate the F/48 slit for long line_2: slit spectroscopy before the high background levels seen in line_3: previous F/48 turn-ons overwhelm the images. The target line_4: was chosen for its large size, well determined features based line_5: on F/96 images, and well-known coordinates. The target will line_6: be acquired using a modified Mode I acquisition procedure line_7: which have been optimized to run in as short a period as line_8: possible. While the SIP is uplinked, an INTFLAT will be line_9: taken to track the geometric stability. Once centered in line_10: the full format, it will be slewed to the expected location line_11: of the slit where it will proceed with a spatial scan. After line_12: completing part of the scan, the images will be downloaded line_13: and analyzed in real-time to determine the location of the line_14: slit. The target will then be SIP'ed to that location for line_15: the remainder of the observations. INTFLATS will be taken line_16: during the decision times to track the camera distortions. question: 3 section: 2 line_1: The proposed sequence for the observations in the proposal line_2: goes as follows: line_3: Turn on F/48 camera HV (approx. 12 minutes duration) line_4: Take INT ACQ image (5 min exp. time) line_5: Download ACQ image; take INTFLAT during decision time line_6: Retain TDRSS link for immediate uplink after INTFLAT line_7: Uplink SIP, start first spatial scan across slit line_8: Run second spatial scan across slit line_9: Dump STR after second spatial scan is completed line_10: Again retain TDRSS link for immediate uplink line_11: Perform INTFLAT during decision time for SIP line_12: Uplink SIP to center target on slit location line_13: Perform third spatial scan line_14: Perform fourth spatial scan line_15: Perform close-out DARK and INTFLAT images line_16: This proposal should be scheduled such that INTFLATS line_17: are performed during all occultation periods. line_18: This proposal NEEDS to be completed within 2-3 hours after line_19: HV turn-on. This prop will take 3 orbits plus Acq and Int's ! !end of general form text general_form_address: lname: NOTA fname: ANTONELLA category: PI inst: SPACE TELESCOPE SCIENCE INSTITUTE ! ! end of general_form_address records fixed_targets: targnum: 1 name_1: NGC1068 descr_1: E,312,907 pos_1: RA=02H 42M 40.69S +/- 0.01S, pos_2: DEC=-00D 00' 47.79" +/- 0.1", equinox: 2000 pm_or_par: NO rv_or_z: Z=0.003 acqpr_1: EXT plate_req: N fluxval_1: V=10.83 ! ! end of fixed targets ! No solar system records found ! No generic target records found exposure_logsheet: ! linenum: 0.100 targname: DARK config: S/C opmode: DATA aperture: NONE num_exp: 1 time_per_exp: 20M priority: 1 comment_1: Attach BDUMPSTR to this alignment comment_2: to force STR to be clean prior comment_3: to start of program ! linenum: 0.200 targname: DARK config: S/C opmode: DATA aperture: NONE num_exp: 1 time_per_exp: 15M priority: 1 comment_1: Special commanding is needed to comment_2: override 75 minute warm-up period. comment_3: SCHEDULE AS CLOSE AS POSSIBLE TO comment_4: 1ST INT ACQ IN OCCULTATION. ! linenum: 0.500 targname: NGC1068 config: FOC/48 opmode: ACQ aperture: 512X1024 sp_element: F430W num_exp: 1 time_per_exp: 5M priority: 1 param_1: PIXEL=50X25 req_1: SEQ .5-7 NO GAP; req_2: CYCLE 4 / 0.1-7.110; req_3: INT ACQ for 2.000; req_4: ORIENT 313D +/- 25D; req_5: DEC TIME 1S comment_3: Downlink/Uplink req. in same orbit ! linenum: 1.000 targname: INTFLAT config: FOC/48 opmode: RESEAU aperture: 512X1024 sp_element: CLEAR num_exp: 1 time_per_exp: 5M priority: 1 param_1: PIXEL=50X25, param_2: LED=GREEN-2, param_3: LED-STEP=16 comment_1: Repeat exposure in each occultation ! linenum: 2.000 targname: NGC1068 config: FOC/48 opmode: SPEC aperture: 256X1024-SLIT sp_element: GRATING,F130LP num_exp: 1 time_per_exp: 8M priority: 1 param_1: PIXEL=25X25 req_1: SPATIAL SCAN; req_2: SAME ORIENT FOR 2.000-7.000 as 0.500; ! linenum: 2.500 targname: INTFLAT config: FOC/48 opmode: RESEAU aperture: 512X1024 sp_element: CLEAR num_exp: 1 time_per_exp: 5M priority: 1 param_1: PIXEL=50X25, param_2: LED=GREEN-2, param_3: LED-STEP=16 comment_1: Repeat exposure in each occultation ! linenum: 3.000 targname: NGC1068 config: FOC/48 opmode: SPEC aperture: 256X1024-SLIT sp_element: GRATING,F130LP num_exp: 1 time_per_exp: 600S priority: 1 param_1: PIXEL=25X25 req_1: SPATIAL SCAN; req_2: RT ANALYSIS comment_1: Dump STR immediately after comment_2: line 3.000 completes ! linenum: 4.000 targname: INTFLAT config: FOC/48 opmode: RESEAU aperture: 512X1024 sp_element: CLEAR num_exp: 1 time_per_exp: 5M priority: 1 param_1: PIXEL=50X25, param_2: LED=GREEN-2, param_3: LED-STEP=16 ! linenum: 5.000 targname: NGC1068 config: FOC/48 opmode: SPEC aperture: 256X1024-SLIT sp_element: GRATING,F130LP num_exp: 1 time_per_exp: 630S priority: 1 param_1: PIXEL=25X25 req_1: SPATIAL SCAN; req_2: REQ UPLINK ! linenum: 6.000 targname: DARK config: FOC/48 opmode: RESEAU aperture: 512X1024 sp_element: CLEAR num_exp: 1 time_per_exp: 5M priority: 1 param_1: PIXEL=50X25 ! linenum: 7.000 targname: INTFLAT config: FOC/48 opmode: RESEAU aperture: 512X1024 sp_element: CLEAR num_exp: 1 time_per_exp: 5M priority: 1 param_1: PIXEL=50X25, param_2: LED=GREEN-2, param_3: LED-STEP=16 linenum: 7.100 targname: DARK config: S/C opmode: DATA aperture: NONE num_exp: 1 time_per_exp: 20M priority: 1 comment_1: Attach BDUMPSTR to this alignment comment_2: to force STR to be dumped at the comment_3: end of this alignment linenum: 7.110 targname: DARK config: S/C opmode: POINTING aperture: V1 num_exp: 1 time_per_exp: 1S priority: 1 comment_1: Needed to force PCS Acq comment_2: in previous orbit. ! end of exposure logsheet scan_data: line_list: 2.000 fgs_scan: cont_dwell: D dwell_pnts: 2 dwell_secs: 480.00 scan_width: 0.0000 scan_length: 1.000 sides_angle: 0.0000 number_lines: 1 scan_rate: 0.0000 first_line_pa: 0.0000 scan_frame: S/C len_offset: 0.000 wid_offset: 0.000 ! line_list: 3.000 fgs_scan: cont_dwell: D dwell_pnts: 3 dwell_secs: 600.00 scan_width: 0.0000 scan_length: 2.000 sides_angle: 180.0000 number_lines: 1 scan_rate: 0.0000 first_line_pa: 180.0000 scan_frame: S/C len_offset: 0.000 wid_offset: 0.000 ! line_list: 5.000 fgs_scan: cont_dwell: D dwell_pnts: 3 dwell_secs: 630.00 scan_width: 0.0000 scan_length: 0.500 sides_angle: 180.0000 number_lines: 1 scan_rate: 0.0000 first_line_pa: 180.0000 scan_frame: S/C len_offset: 0.000 wid_offset: 0.000 ! ! end of scan data