!   $Id: 5605,v 5.1 1994/07/27 19:42:42 pepsa Exp $

coverpage:

  title_1:         COSTAR/FOS FINE ALIGNMENT - X-TILT/Y-TILT
    title_2:       REPEAT OF 4747 WITH NEW TARGET
    proposal_for:  SMC/COS
    pi_title:      DR.
    pi_fname:      GEORGE
    pi_lname:      HARTIG
    pi_inst:       STSCI
    pi_country:    USA
    pi_phone:      (410)338-4966
    keywords_1:    COSTAR, SMOV
    hours_pri:     16.49
    num_pri:       1
    hrs:           Y
! end of coverpage

abstract:

    line_1:        The following activities will take place during this proposal.
    line_3:        1. Perform a 3x3 tilt scan centered on the current best FOS
    line_4:        X-tilt and Y-tilt positions.  Take G160L spectra through
    line_5:        the 4.3 and 0.3 apertures at each scan point, after peaking
    line_6:        up through the 0.3. Separate tilt scans are performed
    line_7:        sequentially on each side of the FOS.

!
! end of abstract

general_form_proposers:

  lname:           TROELTZSCH
    fname:         JOHN
    mi:            R
    inst:          BALL AEROSPACE
    country:       USA

!

  lname:           HARTIG
    fname:         GEORGE
    inst:          SPACE TELESCOPE SCIENCE INSTITUTE
    country:       USA

!
! end of general_form_proposers block

general_form_text:

  question:        2
    section:       1
    line_1:        This activity will satisfy the following COSTAR SMOV
    line_2:        Requirements:
    line_3:        1. Perform FOS fine tilt scan. Take 0.3 and 4.3 spectra
    line_4:        at 9 locations in a 3 x 3 grid.

!

  question:        3
    section:       1
    line_1:        A Binary Search on-board acquisition will be performed to center
    line_2:        the target in the 4.3 arcsec aperture. A deep ACQ image will then
    line_3:        be obtained.
    line_4:        The FOS M1 mirror will then be moved to each of the 9 scan
    line_5:        points, peakups with spectra being taken at each point. Each data
    line_6:        sequence will consist of the following:
    line_7:        1. Peakup in 0.3 with G160L
    line_8:        2. Image mode spectra with G160L in 0.3 and 4.3, with 3 ysteps
    line_10:       The scan grid is shown below. Each grid point is labeled
    line_11:       with an x and y coordinate (x,y) followed by the number order
    line_12:       (#) of the tilt scan X(x,y)-#.  The distance between points
    line_13:       is 42 arcsec.
    line_15:       X(1,3)-05  X(2,3)-04  X(3,3)-03
    line_16:       X(1,2)-02  X(2,2)-01  X(3,2)-06
    line_17:       X(1,1)-09  X(2,1)-08  X(3,1)-07
    line_19:       The entire sequence will be performed first on the FOS/RD side
    line_20:       then repeated on the FOS/BL side.

!

  question:        5
    section:       1
    line_1:        Prerequisites:
    line_2:        1. COSTAR/FOS Coarse Alignment  (4746).
    line_8:        Real-time Requirements: realtime uplink required at start of
    line_9:        observations to set COSTAR FOS mechanisms to best position.
    line_12:       The SEQ 100-219 within 72H was removed to decrease TRANS
    line_13:       run time.  SPSS should manually create this link.

!

  question:        7
    section:       1
    line_1:        Engineering data will be reduced using the ESS and the COSTAR
    line_2:        data analysis system to generate standard sorts and plots.
    line_4:        Sorts and plots will be used to:
    line_5:        1. Verify FOS M1 tilt movements and performance
    line_6:        2. Verify COSTAR electrical performance
    line_8:        Science data will be analyzed using the COSTAR/FOS data analysis
    line_9:        system.  The following analysis will be performed:
    line_11:       1. Calculate the centroid and encircled energy in the image.
    line_12:       2. Calculate the ratio of the 0.3 aper to 4.3 aper flux for each
    line_13:       scan point.  Plot the results vs. X-tilt and Y-tilt.
    line_14:       3. Use the results of steps 1 and 2 and the COSTAR
    line_15:       opto-mechanical model to determine new positions for
    line_16:       the X, and Y Tilt mechanisms.

!

  question:        7
    section:       2
    line_1:        Certain Data Base Updates:
    line_2:        1. None.
    line_4:        Possible Data Base Updates:
    line_5:        1. Update default SHP mirror positions in PDB table file.

!
!end of general form text

general_form_address:

  lname:           Hartig
    fname:         George
    category:      PI
    inst:          STSCI
    addr_1:        3700 San Martin Dr
    city:          Baltimore
    state:         MD
    zip:           21218
    country:       USA
    phone:         410 338-4966

!

  lname:           Troeltzsch
    fname:         John
    mi:            R
    category:      CON
    inst:          Ball Aerospace
    addr_1:        P. O. Box 1062
    city:          Boulder
    state:         CO
    zip:           80306
    country:       USA
    phone:         303 939-5781

!
! end of general_form_address records

fixed_targets:

    targnum:       1
    name_1:        WD0501+527
    name_2:        G191-B2B
    name_3:        GSSS3734-0506
    descr_1:       J,705,702
    pos_1:         RA=05H 05M 30.6S +/- 0.01S,
    pos_2:         DEC=+52D 49' 54.0" +/- 0.2",
    pos_3:         PLATE-ID=0005,
    equinox:       2000
    pm_or_par:     Y
    pos_epoch_bj:  J
    pos_epoch_yr:  1983.10
    ra_pm_val:     0.000497
    ra_pm_unct:    0.000331
    dec_pm_val:    -0.0880
    dec_pm_unct:   0.0050
    comment_1:     THE GUIDE STAR CATALOG NAME
    comment_2:     IS GIVEN.
    fluxnum_1:     1
    fluxval_1:     V = 11.78 +/- 0.02
    fluxnum_2:     2
    fluxval_2:     B = 11.44 +/- 0.02
    fluxnum_3:     3
    fluxval_3:     U = 10.24 +/- 0.02

!
! end of fixed targets

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       1.000
    sequence_1:    DEFINE
    sequence_2:    FOSRED
    targname:      WD0501+527
    config:        FOS/RD
    opmode:        ACQ/PEAK
    aperture:      0.3
    sp_element:    G160L
    wavelength:    1600-2417
    num_exp:       1
    time_per_exp:  10S
    s_to_n:        60
    fluxnum_1:     1
    fluxnum_2:     2
    priority:      1
    param_1:       TYPE=UP,
    param_2:       SEARCH-SIZE-X=5,
    param_3:       SEARCH-SIZE-Y=5,
    param_4:       SCAN-STEP-X=.06,
    param_5:       SCAN-STEP-Y=.06,
    req_1:         ONBOARD ACQ FOR 2.0;
    comment_1:     FOS PEAKUP IN 0.3 APERTURE

!

    linenum:       2.000
    sequence_1:    DEFINE
    sequence_2:    FOSRED
    targname:      WD0501+527
    config:        FOS/RD
    opmode:        IMAGE
    aperture:      0.3
    sp_element:    G160L
    num_exp:       1
    time_per_exp:  60.0S
    s_to_n:        60
    fluxnum_1:     1
    fluxnum_2:     2
    priority:      1
    param_1:       Y-SIZE=3,
    param_2:       Y-SPACE=21.3,
    param_3:       COMB=YES,
    param_4:       SUB-STEP=4,
    comment_1:     FOS SPECTRA IN 0.3 APERTURE

!

    linenum:       3.000
    sequence_1:    DEFINE
    sequence_2:    FOSRED
    targname:      WD0501+527
    config:        FOS/RD
    opmode:        IMAGE
    aperture:      4.3
    sp_element:    G160L
    num_exp:       1
    time_per_exp:  60.0S
    s_to_n:        60
    fluxnum_1:     1
    fluxnum_2:     2
    priority:      1
    param_1:       Y-SIZE=3,
    param_2:       Y-SPACE=21.3,
    param_3:       COMB=YES,
    param_4:       SUB-STEP=4,
    comment_1:     FOS SPECTRA IN 4.3 APERTURE

!

    linenum:       11.000
    sequence_1:    DEFINE
    sequence_2:    FOSBLU
    targname:      WD0501+527
    config:        FOS/BL
    opmode:        ACQ/PEAK
    aperture:      0.3
    sp_element:    G160L
    wavelength:    1150-2480
    num_exp:       1
    time_per_exp:  30S
    s_to_n:        60
    fluxnum_1:     1
    fluxnum_2:     2
    priority:      1
    param_1:       TYPE=UP,
    param_2:       SEARCH-SIZE-X=5,
    param_3:       SEARCH-SIZE-Y=5,
    param_4:       SCAN-STEP-X=.06,
    param_5:       SCAN-STEP-Y=.06,
    req_1:         ONBOARD ACQ FOR 12.0;
    comment_1:     FOS PEAKUP IN 0.3 APERTURE

!

    linenum:       12.000
    sequence_1:    DEFINE
    sequence_2:    FOSBLU
    targname:      WD0501+527
    config:        FOS/BL
    opmode:        IMAGE
    aperture:      0.3
    sp_element:    G160L
    num_exp:       1
    time_per_exp:  180.0S
    s_to_n:        60
    fluxnum_1:     1
    fluxnum_2:     2
    priority:      1
    param_1:       Y-SIZE=3,
    param_2:       Y-SPACE=21.3,
    param_3:       COMB=YES,
    param_4:       SUB-STEP=4,
    comment_1:     FOS SPECTRA IN 0.3 APERTURE

!

    linenum:       13.000
    sequence_1:    DEFINE
    sequence_2:    FOSBLU
    targname:      WD0501+527
    config:        FOS/BL
    opmode:        IMAGE
    aperture:      4.3
    sp_element:    G160L
    num_exp:       1
    time_per_exp:  180.0S
    s_to_n:        60
    fluxnum_1:     1
    fluxnum_2:     2
    priority:      1
    param_1:       Y-SIZE=3,
    param_2:       Y-SPACE=21.3,
    param_3:       COMB=YES,
    param_4:       SUB-STEP=4,
    comment_1:     FOS SPECTRA IN 4.3 APERTURE

!

    linenum:       90.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  20M
    req_1:         REQ UPLINK;
    req_2:         RT ANALYSIS;
    req_3:         BEFORE 100 BY 2H +/- 2H;
    comment_1:     MOVE ALL FOS MECH POSITIONS.

!

    linenum:       100.000
    targname:      WD0501+527
    config:        FOS/RD
    opmode:        ACQ/PEAK
    aperture:      4.3
    sp_element:    G160L
    wavelength:    1600-2417
    num_exp:       1
    time_per_exp:  1.0S
    priority:      1
    param_1:       SEARCH-SIZE-X=1,
    param_2:       SEARCH-SIZE-Y=3,
    param_3:       SCAN-STEP-Y=1.204
    req_1:         ONBOARD ACQ FOR 100.1;
    req_2:         SEQ 100-121 NO GAP;
    req_3:         CYCLE 4 / 90-222

!

    linenum:       100.100
    targname:      WD0501+527
    config:        FOS/RD
    opmode:        ACQ/PEAK
    aperture:      1.0
    sp_element:    G160L
    wavelength:    1600-2417
    num_exp:       1
    time_per_exp:  1.0S
    priority:      1
    param_1:       SEARCH-SIZE-X=6,
    param_2:       SEARCH-SIZE-Y=2,
    param_3:       SCAN-STEP-X=0.602,
    param_4:       SCAN-STEP-Y=0.602
    req_1:         ONBOARD ACQ FOR 100.2;

!

    linenum:       100.200
    targname:      WD0501+527
    config:        FOS/RD
    opmode:        ACQ/PEAK
    aperture:      0.3
    sp_element:    G160L
    wavelength:    1600-2417
    num_exp:       1
    time_per_exp:  2.0S
    fluxnum_1:     1
    priority:      1
    param_1:       SEARCH-SIZE-X=5,
    param_2:       SEARCH-SIZE-Y=5,
    param_3:       SCAN-STEP-X=0.172,
    param_4:       SCAN-STEP-Y=0.172
    req_1:         ONBOARD ACQ FOR 102.;

!

    linenum:       102.000
    sequence_1:    USE
    sequence_2:    FOSRED

!

    linenum:       103.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-42.0
    param_2:       Y-TILT=0.0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 2

!

    linenum:       104.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG +.027,-.188;

!

    linenum:       105.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+42.0,
    param_2:       Y-TILT=+42.0,
    comment_1:     +10 X STEP MOVE TO SCAN POINT 3,
    comment_2:     +5 Y STEP MOVE TO SCAN  POINT 3.

!

    linenum:       107.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG -.215,+.161;

!

    linenum:       108.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=+42.0,
    comment_1:     -5 X STEP MOVE TO SCAN POINT 4

!

    linenum:       108.500
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG -.188,-.027;

!

    linenum:       109.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-42.0,
    param_2:       Y-TILT=+42.0,
    comment_1:     -5 X STEP MOVE TO SCAN POINT 5

!

    linenum:       110.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG -.161,-.215;

!

    linenum:       111.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+42.0,
    param_2:       Y-TILT=0.0,
    comment_1:     +10 X STEP MOVE TO SCAN POINT 6
    comment_2:     -5 Y STEP MOVE TO SCAN POINT 6

!

    linenum:       113.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG -.027,+.188;

!

    linenum:       114.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+42.0,
    param_2:       Y-TILT=-42.0
    comment_1:     -5 Y STEP MOVE TO SCAN POINT 7

!

    linenum:       115.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG +.161,+.215;

!

    linenum:       116.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=-42.0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 8

!

    linenum:       117.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG +.188,+.027;

!

    linenum:       118.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-42.0,
    param_2:       Y-TILT=-42.0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 9

!

    linenum:       119.000
    sequence_1:    USE
    sequence_2:    FOSRED
    req_1:         POS TARG +.215,-.161;

!

    linenum:       120.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0,
    param_2:       Y-TILT=0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 1

!

    linenum:       121.000
    sequence_1:    USE
    sequence_2:    FOSRED

!

    linenum:       200.000
    targname:      WD0501+527
    config:        FOS/BL
    opmode:        ACQ/PEAK
    aperture:      4.3
    sp_element:    G160L
    wavelength:    1150-2480
    num_exp:       1
    time_per_exp:  2.0S
    priority:      1
    param_1:       SEARCH-SIZE-X=1,
    param_2:       SEARCH-SIZE-Y=3,
    param_3:       SCAN-STEP-Y=1.204
    req_1:         ONBOARD ACQ FOR 200.1;
    req_2:         SEQ 200-221.5 NO GAP;

!

    linenum:       200.100
    targname:      WD0501+527
    config:        FOS/BL
    opmode:        ACQ/PEAK
    aperture:      1.0
    sp_element:    G160L
    wavelength:    1150-2480
    num_exp:       1
    time_per_exp:  2.0S
    priority:      1
    param_1:       SEARCH-SIZE-X=6,
    param_2:       SEARCH-SIZE-Y=2,
    param_3:       SCAN-STEP-X=0.602,
    param_4:       SCAN-STEP-Y=0.602
    req_1:         ONBOARD ACQ FOR 200.2;

!

    linenum:       200.200
    targname:      WD0501+527
    config:        FOS/BL
    opmode:        ACQ/PEAK
    aperture:      0.3
    sp_element:    G160L
    wavelength:    1150-2480
    num_exp:       1
    time_per_exp:  4.0S
    fluxnum_1:     1
    priority:      1
    param_1:       SEARCH-SIZE-X=5,
    param_2:       SEARCH-SIZE-Y=5,
    param_3:       SCAN-STEP-X=0.172,
    param_4:       SCAN-STEP-Y=0.172
    req_1:         ONBOARD ACQ FOR 202.;

!

    linenum:       202.000
    sequence_1:    USE
    sequence_2:    FOSBLU

!

    linenum:       203.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-42.0
    param_2:       Y-TILT=0.0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 2

!

    linenum:       204.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG +.188,-.027;

!

    linenum:       205.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+42.0,
    param_2:       Y-TILT=+42.0,
    comment_1:     +10 X STEP MOVE TO SCAN POINT 3,
    comment_2:     +5 Y STEP MOVE TO SCAN POINT 3

!

    linenum:       207.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG -.215,-.161;

!

    linenum:       208.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=+42.0,
    comment_1:     -5 X STEP MOVE TO SCAN POINT 4

!

    linenum:       208.500
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG -.027,-.188;

!

    linenum:       209.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-42.0,
    param_2:       Y-TILT=+42.0,
    comment_1:     -5 X STEP MOVE TO SCAN POINT 5

!

    linenum:       210.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG +.161,-.215;

!

    linenum:       211.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+42.0,
    param_2:       Y-TILT=0.0,
    comment_1:     +10 X STEP MOVE TO SCAN POINT 6,
    comment_2:     -5 Y STEP MOVE TO SCAN POINT 6

!

    linenum:       213.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG -.188,+.027;

!

    linenum:       214.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+42.0,
    param_2:       Y-TILT=-42.0
    comment_1:     -5 Y STEP MOVE TO SCAN POINT 7

!

    linenum:       215.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG -.161,+.215;

!

    linenum:       216.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=-42.0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 8

!

    linenum:       217.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG +.027,+.188;

!

    linenum:       218.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-42.0,
    param_2:       Y-TILT=-42.0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 9

!

    linenum:       219.000
    sequence_1:    USE
    sequence_2:    FOSBLU
    req_1:         POS TARG +.215,+.161;

!

    linenum:       220.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0,
    param_2:       Y-TILT=0
    comment_1:     -5 X STEP MOVE TO SCAN POINT 1

!

    linenum:       221.000
    sequence_1:    USE
    sequence_2:    FOSBLU

!

    linenum:       221.500
    targname:      DARK
    config:        S/C
    opmode:        DATA
    aperture:      NONE
    num_exp:       1
    time_per_exp:  20M
    priority:      1
    req_1:         RT ANALYSIS;
    comment_1:     ATTACH INSTR = BDUMPSTR

!

    linenum:       222.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOS
    num_exp:       1
    time_per_exp:  20M
    req_1:         REQ UPLINK;
    req_2:         RT ANALYSIS;
    req_3:         AFTER 221 BY 12H +/- 2H;
    comment_1:     MOVE ALL FOS MECH POSITIONS.

!
! end of exposure logsheet

! No scan data records found