! $Id: 5569,v 18.1 1994/09/16 17:27:51 pepsa Exp $ coverpage: title_1: WF/PC2 CYCLE 4 CAL: INTERNAL FLATS proposal_for: CAL/WFC pi_fname: MARK pi_lname: CLAMPIN pi_inst: STSCI pi_country: USA pi_phone: (410) 338-4711 wf_pc: Y ! end of coverpage abstract: line_1: This proposal is designed to take internal flats using the cal-channel line_2: visible lamp and the internal source as the illumination source. The line_3: WFPC2 cal-channel source will be used to obtain flat fields for most of line_4: the visible (i.e. F336W - F1042M) WFPC2 filters in order to map the line_5: pixel to pixel non-uniformity of the CCD detectors. These flats will be line_6: used togther with SLTV flat fields and EARTH FLATS to generate line_7: `superflats' which will correct for the instrumental signature. line_8: INTFLATS using WFPC2's internal lamp are also obtained line_9: in the same epoch to provide a baseline comparison of INTFLAT vs line_10: VISFLAT, in the event of a cal-channel system failure. ! ! end of abstract general_form_proposers: lname: CLAMPIN fname: MARK inst: STSCI country: USA ! lname: BAGGETT fname: SYLVIA inst: STSCI country: USA ! ! end of general_form_proposers block general_form_text: question: 2 section: 1 line_1: VISFLAT exposures are required to calibrate the pixel to pixel line_2: non-uniformity of the WFPC2 CCDs. ! question: 5 section: 1 line_1: VISFLAT frames should be grouped into ~40 minute stacks line_2: to minimize use of the cal-channel lamp system. Re-grouping will line_3: be necessary if the DEFAULT exposure times change. NOTE: these line_4: should not be scheduled into back-to-back 3 hour blocks since line_5: this will produce undesirable cycling of the flip mirror motor. line_6: Note that there are two INTFLAT sequences; one set should be line_7: done on shutterblade A, the other set on shutter blade B. line_8: This will require an alignment time increase of 1 minute. ! !end of general form text general_form_address: lname: CLAMPIN fname: MARK category: PI addr_1: 3700 San Martin Drive city: Baltimore state: MD zip: 21218 country: USA phone: (410) 338-4711 ! lname: BAGGETT fname: SYLVIA mi: M category: CI addr_1: 3700 San Martin Drive city: Baltimore state: MD zip: 21218 country: USA phone: (410) 338-5054 ! ! end of general_form_address records ! No fixed target records found ! No solar system records found ! No generic target records found exposure_logsheet: linenum: 10.000 sequence_1: DEF VF targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: # num_exp: 1 time_per_exp: 10S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO req_1: CYCLE 4 / 10-11; ! linenum: 11.000 sequence_1: DEF INT targname: INTFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: # num_exp: 1 time_per_exp: 1S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO, ! linenum: 51.000 sequence_1: USE INT sp_element: F336W time_per_exp: X1000 req_1: CYCLE 4 / 51-66; req_2: GROUP 51-66 NO GAP comment_1: INTFLAT SEQUENCE comment_2: WHOLE SET SHOULD BE DONE ON comment_3: SHUTTERBLADE 'A' comment_4: START WITHIN 1 MONTH OF comment_5: OF TERMINATION OF SMOV 5240 ! linenum: 52.000 sequence_1: USE INT sp_element: F439W time_per_exp: X180 ! linenum: 53.000 sequence_1: USE INT sp_element: F547M time_per_exp: X26 ! linenum: 54.000 sequence_1: USE INT sp_element: F555W time_per_exp: X7 ! linenum: 55.000 sequence_1: USE INT sp_element: F569W time_per_exp: X6 ! linenum: 56.000 sequence_1: USE INT sp_element: F606W time_per_exp: X2 ! linenum: 57.000 sequence_1: USE INT sp_element: F622W time_per_exp: X2.3 ! linenum: 58.000 sequence_1: USE INT sp_element: F631N time_per_exp: X180 ! linenum: 59.000 sequence_1: USE INT sp_element: F502N time_per_exp: X500 ! linenum: 60.000 sequence_1: USE INT sp_element: F656N time_per_exp: X230 ! linenum: 61.000 sequence_1: USE INT sp_element: F675W time_per_exp: X1.4 ! linenum: 62.000 sequence_1: USE INT sp_element: F673N time_per_exp: X18 ! linenum: 63.000 sequence_1: USE INT sp_element: F702W time_per_exp: X0.7 ! linenum: 64.000 sequence_1: USE INT sp_element: F785LP time_per_exp: X0.3 ! linenum: 65.000 sequence_1: USE INT sp_element: F814W time_per_exp: X0.35 ! linenum: 66.000 sequence_1: USE INT sp_element: F1042M time_per_exp: X1.0 ! linenum: 71.000 sequence_1: USE INT sp_element: F336W time_per_exp: X1000 req_1: CYCLE 4 / 71-86; req_2: GROUP 71-86 NO GAP comment_1: INTFLAT SEQUENCE REPEATED comment_2: WHOLE SET SHOULD BE DONE ON comment_3: SHUTTERBLADE 'B' ! linenum: 72.000 sequence_1: USE INT sp_element: F439W time_per_exp: X180 ! linenum: 73.000 sequence_1: USE INT sp_element: F547M time_per_exp: X26 ! linenum: 74.000 sequence_1: USE INT sp_element: F555W time_per_exp: X7 ! linenum: 75.000 sequence_1: USE INT sp_element: F569W time_per_exp: X6 ! linenum: 76.000 sequence_1: USE INT sp_element: F606W time_per_exp: X2 ! linenum: 77.000 sequence_1: USE INT sp_element: F622W time_per_exp: X2.3 ! linenum: 78.000 sequence_1: USE INT sp_element: F631N time_per_exp: X180 ! linenum: 79.000 sequence_1: USE INT sp_element: F502N time_per_exp: X500 ! linenum: 80.000 sequence_1: USE INT sp_element: F656N time_per_exp: X230 ! linenum: 81.000 sequence_1: USE INT sp_element: F675W time_per_exp: X1.4 ! linenum: 82.000 sequence_1: USE INT sp_element: F673N time_per_exp: X18 ! linenum: 83.000 sequence_1: USE INT sp_element: F702W time_per_exp: X0.7 ! linenum: 84.000 sequence_1: USE INT sp_element: F785LP time_per_exp: X0.3 ! linenum: 85.000 sequence_1: USE INT sp_element: F814W time_per_exp: X0.35 ! linenum: 86.000 sequence_1: USE INT sp_element: F1042M time_per_exp: X1.0 ! linenum: 101.100 sequence_1: USE VF sp_element: F300W time_per_exp: X120 req_1: CYCLE 4 / 101.1-108.5; comment_1: ATTEMPT WAS MADE TO LIST EXPOSURES comment_2: TO FORM SETS OF 42 MINUTE ALIGNMENTS comment_3: TO MAXIMIZE USE OF LAMP ON-TIME comment_4: MAY HAVE TO REGROUP IF DEFTIMES CHANGE comment_5: START WITHIN 1 MONTH OF comment_6: OF TERMINATION OF SMOV 5240 ! linenum: 101.200 sequence_1: USE VF sp_element: F380W time_per_exp: X6 ! linenum: 101.300 sequence_1: USE VF sp_element: F469N time_per_exp: X50 ! linenum: 102.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 2200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 103.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 103.200 sequence_1: USE VF sp_element: F410M time_per_exp: X23 ! linenum: 103.300 sequence_1: USE VF sp_element: F437N time_per_exp: X100 ! linenum: 103.400 sequence_1: USE VF sp_element: F467M time_per_exp: X6 ! linenum: 104.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F547M num_exp: 1 time_per_exp: 4S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 104.200 sequence_1: USE VF sp_element: F569W time_per_exp: X0.18 ! linenum: 104.300 sequence_1: USE VF sp_element: F588N time_per_exp: X2.3 ! linenum: 104.400 sequence_1: USE VF sp_element: F606W time_per_exp: X0.05 ! linenum: 104.500 sequence_1: USE VF sp_element: F622W time_per_exp: X0.07 ! linenum: 104.600 sequence_1: USE VF sp_element: F631N time_per_exp: X2.6 ! linenum: 104.700 sequence_1: USE VF sp_element: F658N time_per_exp: X2 ! linenum: 104.800 sequence_1: USE VF sp_element: F702W time_per_exp: X0.05 ! linenum: 104.900 sequence_1: USE VF sp_element: F785LP time_per_exp: X0.1 ! linenum: 104.950 sequence_1: USE VF sp_element: F791W time_per_exp: X0.08 ! linenum: 105.100 sequence_1: USE VF sp_element: F850LP time_per_exp: X.012 ! linenum: 105.200 sequence_1: USE VF sp_element: F953N time_per_exp: X5 ! linenum: 105.300 sequence_1: USE VF sp_element: FQUVN time_per_exp: X180 ! linenum: 106.100 sequence_1: USE VF sp_element: F1042M time_per_exp: X0.8 ! linenum: 107.100 sequence_1: USE VF sp_element: F487N time_per_exp: X30 ! linenum: 107.200 sequence_1: USE VF sp_element: F450W time_per_exp: X1.0 ! linenum: 107.300 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: FQCH4N num_exp: 1 time_per_exp: 10S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 108.100 sequence_1: USE VF sp_element: F336W time_per_exp: X80 ! linenum: 108.200 sequence_1: USE VF sp_element: F439W time_per_exp: X4 ! linenum: 108.300 sequence_1: USE VF sp_element: F555W time_per_exp: X0.16 ! linenum: 108.400 sequence_1: USE VF sp_element: F675W time_per_exp: X0.06 ! linenum: 108.500 sequence_1: USE VF sp_element: F814W time_per_exp: X0.06 ! linenum: 201.100 sequence_1: USE VF sp_element: F300W time_per_exp: X120 req_1: CYCLE 4 / 201.1-208.5; comment_1: ATTEMPT WAS MADE TO LIST EXPOSURES comment_2: TO FORM SETS OF 42 MINUTE ALIGNMENTS comment_3: TO MAXIMIZE USE OF LAMP ON-TIME comment_4: MAY HAVE TO REGROUP IF DEFTIMES CHANGE comment_5: START WITHIN 1 MONTH OF comment_6: OF TERMINATION OF SMOV 5240 ! linenum: 201.200 sequence_1: USE VF sp_element: F380W time_per_exp: X6 ! linenum: 201.300 sequence_1: USE VF sp_element: F469N time_per_exp: X50 ! linenum: 202.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 2200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 203.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 203.200 sequence_1: USE VF sp_element: F410M time_per_exp: X23 ! linenum: 203.300 sequence_1: USE VF sp_element: F437N time_per_exp: X100 ! linenum: 203.400 sequence_1: USE VF sp_element: F467M time_per_exp: X6 ! linenum: 204.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F547M num_exp: 1 time_per_exp: 4S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 204.200 sequence_1: USE VF sp_element: F569W time_per_exp: X0.18 ! linenum: 204.300 sequence_1: USE VF sp_element: F588N time_per_exp: X2.3 ! linenum: 204.400 sequence_1: USE VF sp_element: F606W time_per_exp: X0.05 ! linenum: 204.500 sequence_1: USE VF sp_element: F622W time_per_exp: X0.07 ! linenum: 204.600 sequence_1: USE VF sp_element: F631N time_per_exp: X2.6 ! linenum: 204.700 sequence_1: USE VF sp_element: F658N time_per_exp: X2 ! linenum: 204.800 sequence_1: USE VF sp_element: F702W time_per_exp: X0.05 ! linenum: 204.900 sequence_1: USE VF sp_element: F785LP time_per_exp: X0.1 ! linenum: 204.950 sequence_1: USE VF sp_element: F791W time_per_exp: X0.08 ! linenum: 205.100 sequence_1: USE VF sp_element: F850LP time_per_exp: X.012 ! linenum: 205.200 sequence_1: USE VF sp_element: F953N time_per_exp: X5 ! linenum: 205.300 sequence_1: USE VF sp_element: FQUVN time_per_exp: X180 ! linenum: 206.100 sequence_1: USE VF sp_element: F1042M time_per_exp: X0.8 ! linenum: 207.100 sequence_1: USE VF sp_element: F487N time_per_exp: X30 ! linenum: 207.200 sequence_1: USE VF sp_element: F450W time_per_exp: X1.0 ! linenum: 207.300 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: FQCH4N num_exp: 1 time_per_exp: 10S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 208.100 sequence_1: USE VF sp_element: F336W time_per_exp: X80 ! linenum: 208.200 sequence_1: USE VF sp_element: F439W time_per_exp: X4 ! linenum: 208.300 sequence_1: USE VF sp_element: F555W time_per_exp: X0.16 ! linenum: 208.400 sequence_1: USE VF sp_element: F675W time_per_exp: X0.06 ! linenum: 208.500 sequence_1: USE VF sp_element: F814W time_per_exp: X0.06 ! linenum: 301.100 sequence_1: USE VF sp_element: F300W time_per_exp: X120 req_1: CYCLE 4 / 301.1-308.5; comment_1: ATTEMPT WAS MADE TO LIST EXPOSURES comment_2: TO FORM SETS OF 42 MINUTE ALIGNMENTS comment_3: TO MAXIMIZE USE OF LAMP ON-TIME comment_4: MAY HAVE TO REGROUP IF DEFTIMES CHANGE comment_5: START WITHIN 1 MONTH OF comment_6: OF TERMINATION OF SMOV 5240 ! linenum: 301.200 sequence_1: USE VF sp_element: F380W time_per_exp: X6 ! linenum: 301.300 sequence_1: USE VF sp_element: F469N time_per_exp: X50 ! linenum: 302.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 2200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 303.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 303.200 sequence_1: USE VF sp_element: F410M time_per_exp: X23 ! linenum: 303.300 sequence_1: USE VF sp_element: F437N time_per_exp: X100 ! linenum: 303.400 sequence_1: USE VF sp_element: F467M time_per_exp: X6 ! linenum: 304.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F547M num_exp: 1 time_per_exp: 4S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 304.200 sequence_1: USE VF sp_element: F569W time_per_exp: X0.18 ! linenum: 304.300 sequence_1: USE VF sp_element: F588N time_per_exp: X2.3 ! linenum: 304.400 sequence_1: USE VF sp_element: F606W time_per_exp: X0.05 ! linenum: 304.500 sequence_1: USE VF sp_element: F622W time_per_exp: X0.07 ! linenum: 304.600 sequence_1: USE VF sp_element: F631N time_per_exp: X2.6 ! linenum: 304.700 sequence_1: USE VF sp_element: F658N time_per_exp: X2 ! linenum: 304.800 sequence_1: USE VF sp_element: F702W time_per_exp: X0.05 ! linenum: 304.900 sequence_1: USE VF sp_element: F785LP time_per_exp: X0.1 ! linenum: 304.950 sequence_1: USE VF sp_element: F791W time_per_exp: X0.08 ! linenum: 305.100 sequence_1: USE VF sp_element: F850LP time_per_exp: X.012 ! linenum: 305.200 sequence_1: USE VF sp_element: F953N time_per_exp: X5 ! linenum: 305.300 sequence_1: USE VF sp_element: FQUVN time_per_exp: X180 ! linenum: 306.100 sequence_1: USE VF sp_element: F1042M time_per_exp: X0.8 ! linenum: 307.100 sequence_1: USE VF sp_element: F487N time_per_exp: X30 ! linenum: 307.200 sequence_1: USE VF sp_element: F450W time_per_exp: X1.0 ! linenum: 307.300 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: FQCH4N num_exp: 1 time_per_exp: 10S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 308.100 sequence_1: USE VF sp_element: F336W time_per_exp: X80 ! linenum: 308.200 sequence_1: USE VF sp_element: F439W time_per_exp: X4 ! linenum: 308.300 sequence_1: USE VF sp_element: F555W time_per_exp: X0.16 ! linenum: 308.400 sequence_1: USE VF sp_element: F675W time_per_exp: X0.06 ! linenum: 308.500 sequence_1: USE VF sp_element: F814W time_per_exp: X0.06 ! linenum: 401.100 sequence_1: USE VF sp_element: F300W time_per_exp: X120 req_1: CYCLE 4 / 401.1-408.5; comment_1: ATTEMPT WAS MADE TO LIST EXPOSURES comment_2: TO FORM SETS OF 42 MINUTE ALIGNMENTS comment_3: TO MAXIMIZE USE OF LAMP ON-TIME comment_4: MAY HAVE TO REGROUP IF DEFTIMES CHANGE comment_5: START WITHIN 1 MONTH OF comment_6: OF TERMINATION OF SMOV 5240 ! linenum: 401.200 sequence_1: USE VF sp_element: F380W time_per_exp: X6 ! linenum: 401.300 sequence_1: USE VF sp_element: F469N time_per_exp: X50 ! linenum: 402.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 2200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 403.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 403.200 sequence_1: USE VF sp_element: F410M time_per_exp: X23 ! linenum: 403.300 sequence_1: USE VF sp_element: F437N time_per_exp: X100 ! linenum: 403.400 sequence_1: USE VF sp_element: F467M time_per_exp: X6 ! linenum: 404.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F547M num_exp: 1 time_per_exp: 4S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 404.200 sequence_1: USE VF sp_element: F569W time_per_exp: X0.18 ! linenum: 404.300 sequence_1: USE VF sp_element: F588N time_per_exp: X2.3 ! linenum: 404.400 sequence_1: USE VF sp_element: F606W time_per_exp: X0.05 ! linenum: 404.500 sequence_1: USE VF sp_element: F622W time_per_exp: X0.07 ! linenum: 404.600 sequence_1: USE VF sp_element: F631N time_per_exp: X2.6 ! linenum: 404.700 sequence_1: USE VF sp_element: F658N time_per_exp: X2 ! linenum: 404.800 sequence_1: USE VF sp_element: F702W time_per_exp: X0.05 ! linenum: 404.900 sequence_1: USE VF sp_element: F785LP time_per_exp: X0.1 ! linenum: 404.950 sequence_1: USE VF sp_element: F791W time_per_exp: X0.08 ! linenum: 405.100 sequence_1: USE VF sp_element: F850LP time_per_exp: X.012 ! linenum: 405.200 sequence_1: USE VF sp_element: F953N time_per_exp: X5 ! linenum: 405.300 sequence_1: USE VF sp_element: FQUVN time_per_exp: X180 ! linenum: 406.100 sequence_1: USE VF sp_element: F1042M time_per_exp: X0.8 ! linenum: 407.100 sequence_1: USE VF sp_element: F487N time_per_exp: X30 ! linenum: 407.200 sequence_1: USE VF sp_element: F450W time_per_exp: X1.0 ! linenum: 407.300 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: FQCH4N num_exp: 1 time_per_exp: 10S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 408.100 sequence_1: USE VF sp_element: F336W time_per_exp: X80 ! linenum: 408.200 sequence_1: USE VF sp_element: F439W time_per_exp: X4 ! linenum: 408.300 sequence_1: USE VF sp_element: F555W time_per_exp: X0.16 ! linenum: 408.400 sequence_1: USE VF sp_element: F675W time_per_exp: X0.06 ! linenum: 408.500 sequence_1: USE VF sp_element: F814W time_per_exp: X0.06 ! linenum: 501.100 sequence_1: USE VF sp_element: F300W time_per_exp: X120 req_1: CYCLE 4 / 501.1-508.5; comment_1: ATTEMPT WAS MADE TO LIST EXPOSURES comment_2: TO FORM SETS OF 42 MINUTE ALIGNMENTS comment_3: TO MAXIMIZE USE OF LAMP ON-TIME comment_4: MAY HAVE TO REGROUP IF DEFTIMES CHANGE comment_5: START WITHIN 1 MONTH OF comment_6: OF TERMINATION OF SMOV 5240 ! linenum: 501.200 sequence_1: USE VF sp_element: F380W time_per_exp: X6 ! linenum: 501.300 sequence_1: USE VF sp_element: F469N time_per_exp: X50 ! linenum: 502.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 2200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 503.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F390N num_exp: 1 time_per_exp: 200S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO comment_1: EXPTIME SPECIFIED HERE comment_2: TO SPLIT 2400 S EXPOSURE ! linenum: 503.200 sequence_1: USE VF sp_element: F410M time_per_exp: X23 ! linenum: 503.300 sequence_1: USE VF sp_element: F437N time_per_exp: X100 ! linenum: 503.400 sequence_1: USE VF sp_element: F467M time_per_exp: X6 ! linenum: 504.100 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: F547M num_exp: 1 time_per_exp: 4S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 504.200 sequence_1: USE VF sp_element: F569W time_per_exp: X0.18 ! linenum: 504.300 sequence_1: USE VF sp_element: F588N time_per_exp: X2.3 ! linenum: 504.400 sequence_1: USE VF sp_element: F606W time_per_exp: X0.05 ! linenum: 504.500 sequence_1: USE VF sp_element: F622W time_per_exp: X0.07 ! linenum: 504.600 sequence_1: USE VF sp_element: F631N time_per_exp: X2.6 ! linenum: 504.700 sequence_1: USE VF sp_element: F658N time_per_exp: X2 ! linenum: 504.800 sequence_1: USE VF sp_element: F702W time_per_exp: X0.05 ! linenum: 504.900 sequence_1: USE VF sp_element: F785LP time_per_exp: X0.1 ! linenum: 504.950 sequence_1: USE VF sp_element: F791W time_per_exp: X0.08 ! linenum: 505.100 sequence_1: USE VF sp_element: F850LP time_per_exp: X.012 ! linenum: 505.200 sequence_1: USE VF sp_element: F953N time_per_exp: X5 ! linenum: 505.300 sequence_1: USE VF sp_element: FQUVN time_per_exp: X180 ! linenum: 506.100 sequence_1: USE VF sp_element: F1042M time_per_exp: X0.8 ! linenum: 507.100 sequence_1: USE VF sp_element: F487N time_per_exp: X30 ! linenum: 507.200 sequence_1: USE VF sp_element: F450W time_per_exp: X1.0 ! linenum: 507.300 targname: VISFLAT config: WFPC2 opmode: IMAGE aperture: WFALL sp_element: FQCH4N num_exp: 1 time_per_exp: 10S priority: 1 param_1: ATD-GAIN=7, CR-SPLIT=NO ! linenum: 508.100 sequence_1: USE VF sp_element: F336W time_per_exp: X80 ! linenum: 508.200 sequence_1: USE VF sp_element: F439W time_per_exp: X4 ! linenum: 508.300 sequence_1: USE VF sp_element: F555W time_per_exp: X0.16 ! linenum: 508.400 sequence_1: USE VF sp_element: F675W time_per_exp: X0.06 ! linenum: 508.500 sequence_1: USE VF sp_element: F814W time_per_exp: X0.06 ! ! ! end of exposure logsheet ! No scan data records found