! $Id: 5276,v 4.1 1994/07/27 16:16:45 pepsa Exp $ coverpage: title_1: GHRS SIDE 1 DETECTOR CALIBRATIONS--CYCLE 4 proposal_for: CAL/HRS cont_id: 5040 pi_title: DR. pi_fname: STEPHEN pi_mi: J. pi_lname: HULBERT pi_inst: STSCI pi_country: USA pi_phone: 301-338-4911 keywords_1: HRS, CALIBRATION, DETECTORS, CYCLE 4, SIDE 1 hours_par: 2.22 hrs: Y pi_position: GHRS INSTR SCI ! end of coverpage abstract: line_1: This proposal defines 2 sets of standard line_2: detector tests; a very short set will be run line_3: 4 times per year for each detector, and a line_4: longer set will be run as needed for each detector. line_5: For the lengthened Cycle 4 the short part of this line_6: proposal will run five times -- once every 3 months. ! ! end of abstract general_form_proposers: lname: HULBERT fname: STEPHEN title: DR. mi: J. inst: STSCI country: USA ! lname: SHERBERT fname: LISA title: MS. mi: E. inst: STSCI country: USA ! ! end of general_form_proposers block general_form_text: question: 2 section: 1 line_1: The GHRS digicons require several internal calibrations line_2: to be performed periodically.This proposal is defined so that line_3: an abbreviated test can check the detectors quaterly, and the line_4: full test be performed AS NEEDED. This gives us confidence in line_5: the stability of the detectors, but will not require an line_6: unreasonably large amount of time. ! question: 3 section: 1 line_1: The short test to be run includes: line_2: 1) 70 second dark count measurement line_3: 2) focus check at nominal HV and tweak line_4: 3) 28 sec flat field lamp obs at center coords. line_5: 4) sample mapping function at center Y def. line_6: 5) line mapping function at center X def. line_13: The longer test to be run as needed includes: line_14: 1) complete PMAP line_15: 2) complete sample mapping function (MSKSCN) line_16: 3) complete line mapping function (TOPBOTSCN) ! question: 4 section: 1 line_1: These same calibrations were run on Side 2 several times line_2: during ground based testing in Boulder, and were repeated line_3: during A&V, OV, SV, Cycle 1, Cycle 2 and Cycle 3. line_4: Periodic repeats of this proposal are necessary to line_5: ensure the stability of the detectors. ! question: 5 section: 1 line_1: Exposure times were specified based on measured count line_2: rates with the internal flat field lamps, and the line_3: requirement to obtain approximately 10000 counts per line_4: diode. There are no external targets, and no line_5: special pointing requirements. All of these observations line_6: should be scheduled as interleavers. Both the short and line_7: long test contain several exposures. None of the individual line_8: exposures exceeds 12 minutes. I have asked that for each line_9: test its individual components be grouped within 24 hours. line_10: Execute after successful completion of 5275 and before 5277. line_11: This proposal requires and OK from J. Skapik. It may also line_12: be executed PRIOR to the COSTAR/GHRS deployment. ! question: 6 section: 1 line_1: This prop contains 2 sequences for scheduling: line_2: a) Lines 200 - 204 D1 short test line_3: b) Lines 400 - 403 D1 long test ! question: 7 section: 1 line_1: Standard reductions and output products will be produced. ! question: 8 section: 1 line_1: For lines 200 - 204 I have requested line_2: "group within 24 hours". The goal is simply to obtain line_3: all of the calibrations while the thermal and electro- line_4: optical properties are constant. ! !end of general form text general_form_address: lname: HULBERT fname: STEPHEN mi: J. title: DR. category: PI inst: STSCI ! ! end of general_form_address records ! No fixed target records found ! No solar system records found ! No generic target records found exposure_logsheet: linenum: 1.000 sequence_1: DEF sequence_2: DARKCNT targname: DARK config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 70S priority: 1 param_1: TYPE=SHORT-X, param_2: X=2048, param_3: Y=2048, param_4: SPACING=16, req_1: CYCLE 4/ 1-403; comment_1: USE GHRS DEFAULT OST comment_2: ZDARKPAT comment_3: CHECK THAT EACH BIN OF DATA comment_4: CONTAINS TEN CONSECUTIVE comment_5: SECONDS OF DARK DATA ! linenum: 2.000 sequence_1: DEF sequence_2: FOCUS targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 231.0S s_to_n: 60 priority: 1 param_1: TYPE=LONG-X , param_2: X=1737, param_3: Y=2048, param_4: SPACING=1, comment_1: USE GHRS DEFAULT OST comment_2: ZLONGSCNX comment_3: INITIAL X=1622,Y=2048,DELTAX=1 ! linenum: 3.000 sequence_1: DEF sequence_2: FLATFLD targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 28.0S s_to_n: 100 priority: 1 param_1: TYPE=SHORT-Y, param_2: X=2048, param_3: Y=2048, param_4: SPACING=16, comment_1: 4 SECONDS FOR EACH BIN comment_2: 7 Y DEFLECTIONS CENTERED ON 2048 ! linenum: 4.000 sequence_1: DEF sequence_2: SAMPLE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-X, param_2: X=1380, param_3: Y=2048, param_4: SPACING=40, req_1: SEQ 4-7 NO GAP; comment_1: INITIAL X = 1260 comment_2: DELTA X = 40 comment_3: FINAL X = 1500 ! linenum: 5.000 sequence_1: DEF sequence_2: SAMPLE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-X, param_2: X=1660, param_3: Y=2048, param_4: SPACING=40, comment_1: INITIAL X = 1540 comment_2: DELTA X = 40 comment_3: FINAL X = 1780 comment_4: 4 AND 5 MAP LEFT EDGE AT CENTER Y ! linenum: 6.000 sequence_1: DEF sequence_2: SAMPLE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-X, param_2: X=2450, param_3: Y=2048, param_4: SPACING=40, comment_1: INITIAL X = 2330 comment_2: DELTA X = 40 comment_3: FINAL X = 2570 ! linenum: 7.000 sequence_1: DEF sequence_2: SAMPLE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-X, param_2: X=2730, param_3: Y=2048, param_4: SPACING=40, comment_1: INITIAL X = 2610 comment_2: DELTA X = 40 comment_3: FINAL X = 2850 comment_4: 6 AND 7 MAP RIGHT EDGE AT CENTER Y ! linenum: 8.000 sequence_1: DEF sequence_2: LINE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-Y, param_2: X=2048, param_3: Y=206, param_4: SPACING=32, req_1: SEQ 8-11 NO GAP; comment_1: INITIAL Y = 110 comment_2: DELTA Y = 32 comment_3: FINAL Y = 302 ! linenum: 9.000 sequence_1: DEF sequence_2: LINE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-Y, param_2: X=2048, param_3: Y=430, param_4: SPACING=32, comment_1: INITIAL Y = 334 comment_2: DELTA Y = 32 comment_3: FINAL Y = 526 comment_4: 8 AND 9 MAP TOP EDGE AT CENTER X comment_5: D1 IS NEAR 360, D2 NEAR 240 ! linenum: 10.000 sequence_1: DEF sequence_2: LINE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-Y, param_2: X=2048, param_3: Y=3600, param_4: SPACING=32, comment_1: INITIAL Y = 3504 comment_2: DELTA Y = 32 comment_3: FINAL Y = 3696 ! linenum: 11.000 sequence_1: DEF sequence_2: LINE targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 7S s_to_n: 60 priority: 1 param_1: TYPE=SHORT-Y, param_2: X=2048, param_3: Y=3824, param_4: SPACING=32, comment_1: INITIAL Y = 3728 comment_2: DELTA Y = 32 comment_3: FINAL Y = 3920 comment_4: 10 AND 11 MAP BOTTOM EDGE AT CENTER X comment_5: D1 IS NEAR 3760, D2 NEAR 3700 ! linenum: 12.000 sequence_1: DEF sequence_2: MSKSCN targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 196S s_to_n: 60 priority: 1 param_1: TYPE=MASK, comment_1: USE GHRS DEFAULT OST ZMASKSCN comment_2: 28 LINES OF DATA ! linenum: 13.000 sequence_1: DEF sequence_2: PMAP targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 231S s_to_n: 60 priority: 1 param_1: TYPE=LONG-Y, param_2: X=2048, param_3: Y=2096, param_4: SPACING=16, comment_1: USE GHRS DEFAULT OST ZLONGSCNY comment_2: INITIAL X=2048,Y=256,DELTAY=16 comment_3: 33 LINES OF DATA ! linenum: 14.000 sequence_1: DEF sequence_2: TOPBOTSCN targname: INTFLAT config: HRS opmode: PHOTOSCAN aperture: NONE sp_element: # num_exp: 1 time_per_exp: 231S s_to_n: 60 priority: 1 param_1: # comment_1: USE GHRS DEFAULT OST ZLONGSCNY comment_2: X=2048,DELTAY=1 comment_3: Y SPECIFIED ON LINES 402 ! linenum: 200.000 sequence_1: USE sequence_2: DARKCNT sp_element: SAFE1 req_1: GROUP 200-204 WITHIN 12H; req_2: REPEAT 200-204 EVERY 120D +/- 5D req_3: FOR 4 MORE TIMES comment_1: GROUP 200-204 AS 1 SU. ! linenum: 201.000 sequence_1: USE sequence_2: FOCUS sp_element: SAFE1 time_per_exp: X3 ! linenum: 202.000 sequence_1: USE sequence_2: FLATFLD sp_element: SAFE1 time_per_exp: X3 ! linenum: 203.000 sequence_1: USE sequence_2: SAMPLE sp_element: SAFE1 time_per_exp: X3 ! linenum: 204.000 sequence_1: USE sequence_2: LINE sp_element: SAFE1 time_per_exp: X3 ! linenum: 400.000 sequence_1: USE sequence_2: PMAP sp_element: SAFE1 time_per_exp: X3 req_1: GROUP 400-403 WITHIN 24H; comment_1: SCHEDULE ONLY IF NEEDED. comment_2: LINE 403 AS OWN SU. ! linenum: 401.000 sequence_1: USE sequence_2: MSKSCN sp_element: SAFE1 time_per_exp: X3 comment_1: SCHEDULE ONLY IF NEEDED. comment_2: LINE 401 AS OWN SU. ! linenum: 402.000 sequence_1: USE sequence_2: TOPBOTSCN sp_element: SAFE1 time_per_exp: X3 param_1: TYPE=LONG-Y, param_2: X=2048, param_3: Y=253, param_4: SPACING=1, comment_1: INITIAL Y=138 IN ZLONGSCNY comment_2: SCHEDULE ONLY IF NEEDED. comment_3: LINE 402 AS OWN SU. ! linenum: 403.000 sequence_1: USE sequence_2: TOPBOTSCN sp_element: SAFE1 time_per_exp: X3 param_1: TYPE=LONG-Y, param_2: X=2048, param_3: Y=3706, param_4: SPACING=1, comment_1: INITIAL Y=3591 IN ZLONGSCNY comment_2: SCHEDULE ONLY IF NEEDED. comment_3: LINE 403 AS OWN SU. ! ! end of exposure logsheet ! No scan data records found