!  File:  5022C.PROP
!  Database:  PEPDB
!  Date:  23-FEB-1994:15:52:57

coverpage:

  title_1:         HSP PHOTOMETRIC CALIBRATION-CYCLE 3
    proposal_for:  CAL/HSP
    pi_title:      DR.
    pi_fname:      ROBERT
    pi_mi:         C.
    pi_lname:      BLESS
    pi_inst:       UNIV OF WISCONSIN
    pi_country:    USA
    pi_phone:      (608)262-1715
! end of coverpage

abstract:

    line_1:        This proposal performs the absolute calibration of
    line_2:        the HSP for filters used in the GO or GTO Cycle 3
    line_3:        program.  A relatively bright photometric
    line_4:        standard (V > 9) is observed at through all
    line_5:        the filters being used on each detector.  The
    line_6:        observation is repeated every 2 months to monitor
    line_7:        the calibration and to allow interpolation to points
    line_8:        in between the measurements.

!
! end of abstract

general_form_proposers:

  lname:           BLESS
    fname:         ROBERT
    title:         DR.
    mi:            C.
    inst:          UNIV OF WISCONSIN
    country:       USA

!

  lname:           WALTER
    fname:         LISA
    title:         MS.
    mi:            E.
    inst:          SPACE TELESCOPE SCIENCE INSTITUTE
    country:       USA

!
! end of general_form_proposers block

general_form_text:

  question:        3
    section:       1
    line_1:        All the standard stars to be used have similar
    line_2:        colors in the visual and UV range; they are all
    line_3:        white dwarfs or peculiar O stars with good ground
    line_4:        and space-based photometric calibrations.  A
    line_5:        sequence is defined for each HSP detector with the
    line_6:        relative exposure times in each filter specified.
    line_7:        When the sequence is used, the exposure times are
    line_8:        multiplied by a scale factor which depends on the
    line_9:        brightness of the particular standard star being
    line_10:       observed.   The exposure times (with the multiplier)
    line_11:       are chosen to give about 1E6 counts per filter, so
    line_12:       that the signal-to-noise ratio of the measurement
    line_13:       should be about 1000.  Data are always collected
    line_14:       using DATA-FORMAT=ALL so that the analog-to-digital
    line_15:       conversion can be calibrated for filters with higher
    line_16:       count rates.  The total exposure time for the
    line_17:       observation of a star will usually be determined by
    line_18:       the overhead time required to slew from one filter
    line_19:       to another; the stars were chosen to be bright
    line_20:       enough that the actual time spent collecting data
    line_21:       will not be large.  Since the slew time between
    line_22:       filters is about 30 s, reducing the exposure times
    line_23:       below about 10s is a wasteful efficiency.

!

  question:        5
    section:       1
    line_1:        The observation is to be repeated a total of 6
    line_2:        different times through the year, with possibly a
    line_3:        different target being used each time depending on
    line_4:        which targets are far from the Sun and which are
    line_5:        conveniently located in the sky near other HST
    line_6:        targets (or which are being used for other HST
    line_7:        calibration observations.)  This cannot be specified
    line_8:        very well on the forms, but that is our intention.

!

  question:        6
    section:       1
    line_1:        No special calibrations, dark time, or uninterupted
    line_2:        exposures are requested.

!

  question:        7
    section:       1
    line_1:        The data will be reduced by comparing the count
    line_2:        rates in the various observations with synthetic
    line_3:        photometry based on the HSP filter and detector
    line_4:        response curves and the absolute spectrophotometry
    line_5:        of our standard stars in CDBS.  If HSP is very
    line_6:        stable (as is hoped), then these HSP observations
    line_7:        can be used to improve the relative calibration of
    line_8:        the HST standards.  Results from the analysis will
    line_9:        be used to populate the relative sensitivity
    line_10:       parameters in CDBS for use in pipeline calibration
    line_11:       of HSP data.

!

  question:        8
    section:       1
    line_1:        No supporting or coordinated observations with other
    line_2:        facilites are anticipated.

!

  question:        10
    section:       1
    line_1:        Data reduction and analysis will be carried out at
    line_2:        STScI with CDBS.

!
!end of general form text

general_form_address:

  lname:           BLESS
    fname:         ROBERT
    mi:            C.
    category:      PI
    inst:          UNIV OF WISCONSIN
    addr_1:        475 N. CHARTER
    city:          MADISON
    state:         WI
    zip:           53706
    country:       USA
    phone:         (608)262-1715

!

  lname:           WALTER
    fname:         LISA
    mi:            E.
    category:      CON
    inst:          SPACE TELESCOPE SCIENCE INSTITUTE
    addr_1:        3700 SAN MARTIN DRIVE
    city:          BALTIMORE
    state:         MD
    zip:           21218
    country:       USA
    phone:         (301) 338-5036

!
! end of general_form_address records

fixed_targets:

    targnum:       6
    name_1:        BD+75D325
    name_2:        GSC4380-2196
    descr_1:       J,702
    pos_1:         RA=08H 10M 49.31S +/- 0.5",
    pos_2:         DEC=+74D 57' 57.5" +/- 0.5",
    pos_3:         PLATE-ID=00LQ
    equinox:       2000
    pm_or_par:     NO
    fluxnum_1:     1
    fluxval_1:     V=9.54,B-V=-0.32,
    fluxval_2:     TYPE=O5P

!
! end of fixed targets

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       1.000
    sequence_1:    DEFINE
    sequence_2:    UV1
    targname:      #
    config:        HSP/UV1
    opmode:        ACQ
    num_exp:       1
    time_per_exp:  1S
    fluxnum_1:     1
    priority:      #
    req_1:         ONBOARD ACQ FOR   3-13;
    req_2:         SEQ 1-13 NO GAP;

!

    linenum:       3.000
    sequence_1:    DEFINE
    sequence_2:    UV1
    targname:      #
    config:        HSP/UV1
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F135W
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       7.000
    sequence_1:    DEFINE
    sequence_2:    UV1
    targname:      #
    config:        HSP/UV1
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F218M
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       8.000
    sequence_1:    DEFINE
    sequence_2:    UV1
    targname:      #
    config:        HSP/UV1
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F220W
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       13.000
    sequence_1:    DEFINE
    sequence_2:    UV1
    targname:      #
    config:        HSP/UV1
    opmode:        PRISM
    aperture:      1.0
    sp_element:    F248M/F135W
    time_per_exp:  360S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=1.0,
    param_3:       2ND-SAMPLE=1.0,

!

    linenum:       14.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        ACQ
    num_exp:       1
    time_per_exp:  1S
    fluxnum_1:     1
    priority:      #
    req_1:         ONBOARD ACQ FOR  16-27;
    req_2:         SEQ  14-27 NO GAP;

!

    linenum:       16.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F145M
    time_per_exp:  180S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       19.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F184W
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       20.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F218M
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       21.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F248M
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       23.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F278N
    time_per_exp:  180S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       24.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F284M
    time_per_exp:  60S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       25.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F140LP
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       27.000
    sequence_1:    DEFINE
    sequence_2:    UV2
    targname:      #
    config:        HSP/UV2
    opmode:        PRISM
    aperture:      1.0
    sp_element:    F262M/F145M
    time_per_exp:  420S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=1.0,
    param_3:       2ND-SAMPLE=1.0,

!

    linenum:       28.000
    sequence_1:    DEFINE
    sequence_2:    VIS
    targname:      #
    config:        HSP/VIS
    opmode:        ACQ
    num_exp:       1
    time_per_exp:  1S
    fluxnum_1:     1
    priority:      #
    req_1:         ONBOARD ACQ FOR  35-40;
    req_2:         SEQ  28-40 NO GAP;

!

    linenum:       35.000
    sequence_1:    DEFINE
    sequence_2:    VIS
    targname:      #
    config:        HSP/VIS
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F551W
    time_per_exp:  60S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       37.000
    sequence_1:    DEFINE
    sequence_2:    VIS
    targname:      #
    config:        HSP/VIS
    opmode:        SINGLE
    aperture:      1.0
    sp_element:    F160LP
    time_per_exp:  30S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       39.000
    sequence_1:    DEFINE
    sequence_2:    VIS
    targname:      #
    config:        HSP/VIS
    opmode:        PRISM
    aperture:      1.0
    sp_element:    F551W/F240W
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=1.0,
    param_3:       2ND-SAMPLE=1.0,

!

    linenum:       40.000
    sequence_1:    DEFINE
    sequence_2:    VIS
    targname:      #
    config:        HSP/PMT/VIS
    opmode:        SPLIT
    aperture:      1.0
    sp_element:    F750W/F320N
    time_per_exp:  90S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       41.000
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        ACQ
    num_exp:       1
    time_per_exp:  1S
    fluxnum_1:     1
    priority:      #
    req_1:         ONBOARD ACQ FOR  42-45.3;
    req_2:         SEQ  41-45.3 NO GAP;

!

    linenum:       42.000
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL0
    sp_element:    F216M
    time_per_exp:  240S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,
    req_1:         SEQ 42-42.3 NON-INT;

!

    linenum:       42.100
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL45
    sp_element:    F216M
    time_per_exp:  240S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       42.200
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL90
    sp_element:    F216M
    time_per_exp:  240S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       42.300
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL135
    sp_element:    F216M
    time_per_exp:  240S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       43.000
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL0
    sp_element:    F237M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,
    req_1:         SEQ43-43.3 NON-INT;

!

    linenum:       43.100
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL45
    sp_element:    F237M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       43.200
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL90
    sp_element:    F237M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       43.300
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL135
    sp_element:    F237M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       44.000
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL0
    sp_element:    F277M
    time_per_exp:  120S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,
    req_1:         SEQ 44-44.3 NON-INT;

!

    linenum:       44.100
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL45
    sp_element:    F277M
    time_per_exp:  120S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       44.200
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL90
    sp_element:    F277M
    time_per_exp:  120S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       44.300
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL135
    sp_element:    F277M
    time_per_exp:  120S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       45.000
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL0
    sp_element:    F327M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,
    req_1:         SEQ 45-45.3 NON-INT;

!

    linenum:       45.100
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL45
    sp_element:    F327M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       45.200
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL90
    sp_element:    F327M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       45.300
    sequence_1:    DEFINE
    sequence_2:    POL
    targname:      #
    config:        HSP/POL
    opmode:        SINGLE
    aperture:      POL135
    sp_element:    F327M
    time_per_exp:  150S
    s_to_n:        1000
    fluxnum_1:     1
    priority:      #
    param_1:       DATA-FORMAT=ALL,
    param_2:       SAMPLE-TIME=0.010,

!

    linenum:       47.000
    sequence_1:    USE
    sequence_2:    UV1
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1
    req_1:         SEQ 47-50 NO GAP;
    req_2:         CYCLE 3 /47-450;
    req_3:         AT 20-AUG-1993 +/- 14D;

!

    linenum:       48.000
    sequence_1:    USE
    sequence_2:    VIS
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       49.000
    sequence_1:    USE
    sequence_2:    UV2
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       50.000
    sequence_1:    USE
    sequence_2:    POL
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       147.000
    sequence_1:    USE
    sequence_2:    UV1
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1
    req_1:         SEQ 147-150 NO GAP;
    req_2:         AT 15-OCT-1993 +/- 14D;

!

    linenum:       148.000
    sequence_1:    USE
    sequence_2:    VIS
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       149.000
    sequence_1:    USE
    sequence_2:    UV2
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       150.000
    sequence_1:    USE
    sequence_2:    POL
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       247.000
    sequence_1:    USE
    sequence_2:    UV1
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1
    req_1:         SEQ 247-250 NO GAP;
    req_2:         AT 11-DEC-1993 +/- 14D;

!

    linenum:       248.000
    sequence_1:    USE
    sequence_2:    VIS
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       249.000
    sequence_1:    USE
    sequence_2:    UV2
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       250.000
    sequence_1:    USE
    sequence_2:    POL
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       347.000
    sequence_1:    USE
    sequence_2:    UV1
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1
    req_1:         SEQ 347-350 NO GAP;
    req_2:         AT 04-FEB-1994 +/- 14D;

!

    linenum:       348.000
    sequence_1:    USE
    sequence_2:    VIS
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       349.000
    sequence_1:    USE
    sequence_2:    UV2
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       350.000
    sequence_1:    USE
    sequence_2:    POL
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       447.000
    sequence_1:    USE
    sequence_2:    UV1
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1
    req_1:         SEQ 447-450 NO GAP;
    req_2:         AT 25-MAR-1994 +/- 14D;

!

    linenum:       448.000
    sequence_1:    USE
    sequence_2:    VIS
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       449.000
    sequence_1:    USE
    sequence_2:    UV2
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!

    linenum:       450.000
    sequence_1:    USE
    sequence_2:    POL
    targname:      BD+75D325
    time_per_exp:  X0.2
    priority:      1

!
! end of exposure logsheet

! No scan data records found