!   $Id: 4813,v 4.1 1994/07/27 14:53:19 pepsa Exp $

coverpage:

  title_1:         COSTAR SENSOR STABILITY TEST
    proposal_for:  SME/COS
    pi_fname:      JOHN
    pi_mi:         R
    pi_lname:      TROELTZSCH
    pi_inst:       BALL AEROSPACE
    pi_country:    USA
    pi_phone:      303 939-5781
    keywords_1:    COSTAR, SMOV
    hours_par:     18.00
! end of coverpage

abstract:

    line_1:        The following activities will take place during this proposal.
    line_3:        1. Enable FOC mechanism sensors for 6 hours
    line_5:        2. Enable FOS mechanism sensors for 6 hours
    line_7:        3. Enable GHRS mechanism sensors for 6 hours

!
! end of abstract

general_form_proposers:

  lname:           TROELTZSCH
    fname:         JOHN
    mi:            R
    inst:          BALL AEROSPACE
    country:       USA

!

  lname:           HARTIG
    fname:         GEORGE
    inst:          SPACE TELESCOPE SCIENCE INSTITUTE
    country:       USA

!
! end of general_form_proposers block

general_form_text:

  question:        2
    section:       1
    line_1:        This test will satisfy the following COSTAR ORV Requirements:
    line_3:        1. Determine the orbital stability of each of the types of
    line_4:        COSTAR sensors over a typical 6 hour period.
    line_6:        This proposal implements SMOV activity P0026.

!

  question:        3
    section:       1
    line_1:        This test will begin with the COSTAR instrument in HOLD mode.
    line_2:        The FOC M1 and M2 mirror arms should be deployed, if possible.
    line_3:        There are no requirements on the position of the FOS or GHRS
    line_4:        M2 mirror arms since the related sensors are located on the
    line_5:        M1 mechanisms.
    line_7:        COSTAR will be transitioned to OPERATE mode via stored
    line_8:        commands, and the FOC DITS will be turned on for 6 hours.
    line_9:        The FOC DITS will then be turned off and the FOS DITS will
    line_10:       be turned on for 6 hours.  The FOS DITS will then be
    line_11:       turned off and the GHRS DITS will be turned on for 6
    line_12:       hours.  COSTAR will then be placed back into HOLD mode.

!

  question:        6
    section:       1
    line_1:        Prerequisites:
    line_2:        1. P0020 (4815), COSTAR DOB/FOS M2 Mirror Arm Deployment must
    line_3:        have been completed, and the DOB must be positioned
    line_4:        within the 20 mm nominal operation range.
    line_6:        2. P0021 (4812), COSTAR FOC M1/M2 Mirror Arm Deployment
    line_8:        Real-time Requirements:
    line_10:       None.

!

  question:        7
    section:       1
    line_1:
    line_2:        Engineering data will be reduced using the ESS and the COSTAR
    line_3:        data analysis system to generate standard sorts and plots.
    line_5:        Sorts and plots will be used to:
    line_6:        1. Measure DIT, LVDT, and potentiometer outputs
    line_7:        2. Verify COSTAR electrical performance
    line_9:        Certain Data Base Updates:
    line_10:       None
    line_12:       Possible Data Base Updates:
    line_13:       1. Sensor telemetry calibration curves to increase/decrease
    line_14:       sensor accuracy
    line_15:       2. Temperature telemetry limits

!
!end of general form text

general_form_address:

  lname:           Troeltzsch
    fname:         John
    mi:            R
    category:      PI
    inst:          Ball Aerospace
    addr_1:        P. O. Box 1062
    city:          Boulder
    state:         CO
    zip:           80306
    country:       USA
    phone:         303 939-5781

!
! end of general_form_address records

! No fixed target records found

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       1.000
    targname:      NONE
    config:        COSTAR
    opmode:        SENSOR
    num_exp:       1
    time_per_exp:  6.0H
    priority:      1
    param_1:       MECH=FOC
    req_1:         SEQ 1.0-3.0; PAR;
    req_2:         CYCLE 4 / 1.0-3.0
    comment_1:     USE STORED COMMANDS TO CONFIGURE
    comment_2:     COSTAR TO OP MODE, AND ENABLE FOC
    comment_3:     SENSORS.

!

    linenum:       2.000
    targname:      NONE
    config:        COSTAR
    opmode:        SENSOR
    num_exp:       1
    time_per_exp:  6.0H
    priority:      1
    param_1:       MECH=FOS
    req_1:         PAR;
    comment_1:     USE STORED COMMANDS TO CONFIGURE
    comment_2:     COSTAR TO OP MODE, AND ENABLE FOS
    comment_3:     SENSORS.

!

    linenum:       3.000
    targname:      NONE
    config:        COSTAR
    opmode:        SENSOR
    num_exp:       1
    time_per_exp:  6.0H
    priority:      1
    param_1:       MECH=GHRS
    req_1:         PAR;
    comment_1:     USE STORED COMMANDS TO CONFIGURE
    comment_2:     COSTAR TO OP MODE, AND ENABLE GHRS
    comment_3:     SENSORS.

!
! end of exposure logsheet

! No scan data records found