!   $Id: 4734,v 4.1 1994/07/27 14:36:30 pepsa Exp $

coverpage:

  title_1:         COSTAR/FOC FINE ALIGNMENT
    proposal_for:  SMC/COS
    pi_title:      DR.
    pi_fname:      GEORGE
    pi_lname:      HARTIG
    pi_inst:       STSCI
    pi_country:    USA
    pi_phone:      (410)338-4966
    keywords_1:    COSTAR, SMOV
    hours_pri:     4.45
    num_pri:       1
    foc:           Y
! end of coverpage

abstract:

    line_1:        The following activities will take place during this proposal.
    line_3:        1. Perform a 3x3 tilt scan centered on the current best FOC
    line_4:        X-tilt and Y-tilt positions.  Take an FOC image at each scan
    line_5:        point.
    line_6:        Perform a fine focus sweep.  +/- 2, 1 mm and take an FOC image
    line_7:        at each DOB point.

!
! end of abstract

general_form_proposers:

  lname:           TROELTZSCH
    fname:         JOHN
    mi:            R
    inst:          BALL AEROSPACE
    country:       USA

!

  lname:           HARTIG
    fname:         GEORGE
    inst:          SPACE TELESCOPE SCIENCE INSTITUTE
    country:       USA

!

  lname:           JEDRZEJEWSKI
    fname:         ROBERT
    inst:          SPACE TELESCOPE SCIENCE INSTITUTE
    country:       USA

!
! end of general_form_proposers block

general_form_text:

  question:        2
    section:       1
    line_1:        This activity will satisfy the following COSTAR SMOV
    line_2:        Requirements:
    line_3:        1. Perform FOC fine tilt scan. Take FOC images at 9 locations
    line_4:        in a 3 x 3 grid.
    line_5:        2. Perform FOC fine focus sweep.  Take FOC images at 4 DOB
    line_6:        positions:  +/-2mm, +/- 1mm.

!

  question:        3
    section:       1
    line_1:        An interactive target execution will be executed to acquire
    line_2:        the target into the FOC F/96 aperture. Next, an FOC image will
    line_3:        be taken with the DOB and FOC tilt mechanisms at their current
    line_4:        optimum positions as determined by the COSTAR/FOC Phase Retrieval
    line_5:        test.
    line_7:        The FOC M1 mirror will then be moved to each of the 9 scan
    line_8:        points with an FOC image being taken at each point. The scan
    line_9:        grid is shown below. Each grid point is labeled with an x and y
    line_10:       coordinate (x,y) followed by the number order (#) of the tilt scan
    line_11:       X(x,y)-#.  The distance between points is 30arcsec (=4 tilt steps).
    line_13:       X(1,3)-05  X(2,3)-04  X(3,3)-03
    line_15:       X(1,2)-02  X(2,2)-01  X(3,2)-06
    line_17:       X(1,1)-09  X(2,1)-08  X(3,1)-07

!

  question:        5
    section:       1
    line_1:        Prerequisites:
    line_2:        1. The first series of the COSTAR/FOC Phase Retrieval Test (4735)
    line_8:        Real-time Requirements: None
    line_10:       Target Selection:  3 targets are provided.  They are used in the exposure
    line_11:       logsheet in the preferred order fo BPM16274, HZ21, HZ4.

!

  question:        7
    section:       1
    line_1:        Engineering data will be reduced using the ESS and the COSTAR
    line_2:        data analysis system to generate standard sorts and plots.
    line_4:        Sorts and plots will be used to:
    line_5:        1. Verify FOC tilt movements and performance
    line_6:        2. Verify COSTAR electrical performance
    line_8:        Science data will be analyzed using the COSTAR/FOC data analysis
    line_9:        system.  The following analysis will be performed:
    line_11:       1. Calculate the centroid and encircled energy for each image
    line_12:       and plot the results vs. X-tilt and Y-tilt position.
    line_13:       2. Run phase retrieval on the most out of focus image
    line_14:       on either side of optimal focus to determine the optical
    line_15:       aberrations (Zernike coefficients).
    line_16:       3. Use the results of steps 1 and 2 and the COSTAR
    line_17:       opto-mechanical model to determine new positions for
    line_18:       DOB and X and Y Tilt mechanisms.

!

  question:        7
    section:       2
    line_1:        Certain Data Base Updates:
    line_2:        1. None.
    line_4:        Possible Data Base Updates:
    line_5:        1. Update default SHP mirror positions in PDB table file.

!
!end of general form text

general_form_address:

  lname:           Hartig
    fname:         George
    category:      PI
    inst:          STSCI
    addr_1:        3700 San Martin Dr
    city:          Baltimore
    state:         MD
    zip:           21218
    country:       USA
    phone:         410 338-4966

!

  lname:           Jedrzejewski
    fname:         Robert
    category:      CON
    inst:          STSCI
    addr_1:        3700 San Martin Dr
    city:          Baltimore
    state:         MD
    zip:           21218
    country:       USA
    phone:         410 338-4817

!

  lname:           Troeltzsch
    fname:         John
    mi:            R
    inst:          Ball Aerospace
    addr_1:        P. O. Box 1062
    city:          Boulder
    state:         CO
    zip:           80306
    country:       USA
    phone:         303 939-5781

!
! end of general_form_address records

fixed_targets:

    targnum:       1
    name_1:        BPM16274
    descr_1:       J,701,704
    pos_1:         RA=00H 50M 03.2S +/- 0.1S,
    pos_2:         DEC=-52D 08' 17.4" +/- 1",
    pos_3:         PLATE-ID=02PU
    equinox:       2000
    comment_1:     TARGETS ARE LISTED IN PRIORITY
    comment_2:     ORDER.
    fluxnum_1:     1
    fluxval_1:     V = 14.20 +/- 0.2
    fluxnum_2:     2
    fluxval_2:     TYPE=DA2

!

    targnum:       2
    name_1:        HZ21
    descr_1:       J,704
    pos_1:         RA= 12H 13M 56.42S +/- 0.2S,
    pos_2:         DEC=+32D 56' 30.8" +/- 0.5",
    pos_3:         PLATE-ID=00Y2
    equinox:       2000
    fluxnum_1:     1
    fluxval_1:     V = 14.58 +/- 0.2
    fluxnum_2:     2
    fluxval_2:     B-V = -0.45

!

    targnum:       3
    name_1:        HZ4
    descr_1:       J,704
    pos_1:         RA=03H 55M 21.70S +/- 0.1S,
    pos_2:         DEC=+09D 47' 18.7" +/- 1",
    pos_3:         PLATE-ID=02HA
    equinox:       2000
    fluxnum_1:     1
    fluxval_1:     V = 14.52 +/- 0.2

!
! end of fixed targets

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       1.000
    sequence_1:    DEFINE
    sequence_2:    FOCIMAGE
    targname:      #
    config:        FOC/96
    opmode:        IMAGE
    aperture:      256X256
    sp_element:    F486N
    num_exp:       1
    time_per_exp:  1000S
    s_to_n:        20
    fluxnum_1:     1
    priority:      1
    comment_1:     STANDARD FOC IMAGE

!

    linenum:       2.000
    targname:      BPM16274
    config:        FOC/96
    opmode:        ACQ
    aperture:      512X1024
    sp_element:    F486N
    num_exp:       1
    time_per_exp:  10M
    priority:      1
    param_1:       PIXEL=50X25,
    req_1:         INT ACQ FOR 2.5;
    req_2:         SEQ 2.0-28.0 NO GAP;
    req_3:         CYCLE 4 / 2.0-230.0;
    req_4:         SELECT 1 OF 2-30 OR 102-130 OR
    req_5:         202-230; COND IF BPM AVAILABLE/
    req_6:         2-30;

!

    linenum:       2.500
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       3.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30,
    param_2:       Y-TILT=0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 2

!

    linenum:       4.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       5.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=+30.0
    comment_1:     +60 ARCSEC X +30 ARCSEC Y
    comment_2:     MOVE TO SCAN POINT 3

!

    linenum:       6.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       7.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=+30.0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 4

!

    linenum:       8.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       9.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=+30.0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 5

!

    linenum:       10.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       11.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=0.0,
    comment_1:     +60 ARCSEC X, -30 ARCSEC Y
    comment_2:     MOVE TO SCAN POINT 6

!

    linenum:       12.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       13.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC Y MOVE TO SCAN POINT 7

!

    linenum:       14.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       15.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 8

!

    linenum:       16.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       17.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 9

!

    linenum:       18.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274
    comment_1:     TILT TO HOME POSITION AFTER
    comment_2:     THIS IMAGE.

!

    linenum:       19.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0,
    param_2:       Y-TILT=0,

!

    linenum:       19.500
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       20.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=-112,
    comment_1:     COSTAR DOB -2MM MOVE

!

    linenum:       21.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       22.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=-55,
    comment_1:     COSTAR DOB -1MM MOVE

!

    linenum:       23.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       24.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=+63,
    comment_1:     COSTAR DOB +1MM MOVE

!

    linenum:       25.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       26.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=+124
    comment_1:     COSTAR DOB +2MM MOVE

!

    linenum:       27.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      BPM16274

!

    linenum:       28.000
    targname:      DARK
    config:        S/C
    opmode:        DATA
    aperture:      NONE
    num_exp:       1
    time_per_exp:  20M
    priority:      1
    req_1:         RT ANALYSIS;
    comment_1:     ATTACH INSTR = BDUMPSTR

!

    linenum:       29.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  30M
    priority:      1
    req_1:         REQ UPLINK;
    req_2:         AFTER 27 BY 24H;
    comment_1:     SET COSTAR DOB POSITION

!

    linenum:       30.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  30M
    priority:      1
    req_1:         REQ UPLINK;
    req_2:         AFTER 29;
    comment_1:     SET COSTAR FOC TILTS

!

    linenum:       102.000
    targname:      HZ21
    config:        FOC/96
    opmode:        ACQ
    aperture:      512X1024
    sp_element:    F486N
    num_exp:       1
    time_per_exp:  10M
    priority:      1
    param_1:       PIXEL=50X25,
    req_1:         INT ACQ FOR 102.5;
    req_2:         SEQ 102-128 NO GAP;
    req_3:         COND IF BPM NOT AVAILABLE/
    req_4:         102-130;

!

    linenum:       102.500
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       103.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 2

!

    linenum:       104.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       105.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=+30.0
    comment_1:     +60 ARCSEC X +30 ARCSEC Y
    comment_2:     MOVE TO SCAN POINT 3

!

    linenum:       106.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       107.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=+30.0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 4

!

    linenum:       108.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       109.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=+30.0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 5

!

    linenum:       110.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       111.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=0.0,
    comment_1:     +60 ARCSEC X, -30 ARCSEC Y
    comment_2:     MOVE TO SCAN POINT 6

!

    linenum:       112.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       113.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC Y MOVE TO SCAN POINT 7

!

    linenum:       114.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       115.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 8

!

    linenum:       116.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       117.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 9

!

    linenum:       118.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21
    comment_1:     FOC TILT TO HOME POSITION
    comment_2:     AFTER THIS IMAGE.

!

    linenum:       119.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0,
    param_2:       Y-TILT=0,

!

    linenum:       119.500
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       120.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=-112
    comment_1:     COSTAR DOB -2MM MOVE

!

    linenum:       121.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       122.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=-55,
    comment_1:     COSTAR DOB -1MM MOVE

!

    linenum:       123.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       124.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=+63,
    comment_1:     COSTAR DOB +1MM MOVE

!

    linenum:       125.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       126.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=+124,
    comment_1:     COSTAR DOB +2MM MOVE

!

    linenum:       127.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ21

!

    linenum:       128.000
    targname:      DARK
    config:        S/C
    opmode:        DATA
    aperture:      NONE
    num_exp:       1
    time_per_exp:  20M
    priority:      1
    req_1:         RT ANALYSIS;
    comment_1:     ATTACH INSTR = BDUMPSTR

!

    linenum:       129.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  30M
    priority:      1
    req_1:         REQ UPLINK;
    req_2:         AFTER 127 BY 24H;
    comment_1:     SET COSTAR DOB POSITION

!

    linenum:       130.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  30M
    priority:      1
    req_1:         REQ UPLINK;
    req_2:         AFTER 129;
    comment_1:     SET COSTAR FOC TILTS

!

    linenum:       202.000
    targname:      HZ4
    config:        FOC/96
    opmode:        ACQ
    aperture:      512X1024
    sp_element:    F486N
    num_exp:       1
    time_per_exp:  10M
    priority:      1
    param_1:       PIXEL=50X25,
    req_1:         INT ACQ FOR 202.5;
    req_2:         SEQ 202.0-228.0 NO GAP;
    req_3:         COND IF HZ21 NOT AVAILABLE/
    req_4:         202-230;

!

    linenum:       202.500
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       203.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 2

!

    linenum:       204.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       205.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=+30.0
    comment_1:     +60 ARCSEC X +30 ARCSEC Y
    comment_2:     MOVE TO SCAN POINT 3

!

    linenum:       206.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       207.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=+30.0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 4

!

    linenum:       208.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       209.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=+30.0,
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 5

!

    linenum:       210.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       211.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=0.0,
    comment_1:     +60 ARCSEC X, -30 ARCSEC Y
    comment_2:     MOVE TO SCAN POINT 6

!

    linenum:       212.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       213.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=+30.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC Y MOVE TO SCAN POINT 7

!

    linenum:       214.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       215.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 8

!

    linenum:       216.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       217.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=-30.0,
    param_2:       Y-TILT=-30.0
    comment_1:     -30 ARCSEC X MOVE TO SCAN POINT 9

!

    linenum:       218.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4
    comment_1:     COSTAR FOC TILTS TO HOME
    comment_2:     POSITION AFTER THIS IMAGE.

!

    linenum:       219.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       X-TILT=0,
    param_2:       Y-TILT=0

!

    linenum:       219.500
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       220.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=-112
    comment_1:     COSTAR DOB -2MM MOVE

!

    linenum:       221.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       222.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=-55,
    comment_1:     COSTAR DOB -1MM MOVE

!

    linenum:       223.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       224.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=+63,
    comment_1:     COSTAR DOB +1MM MOVE

!

    linenum:       225.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       226.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  0.0S
    priority:      1
    param_1:       FOCUS=+124,
    comment_1:     COSTAR DOB +2MM MOVE

!

    linenum:       227.000
    sequence_1:    USE
    sequence_2:    FOCIMAGE
    targname:      HZ4

!

    linenum:       228.000
    targname:      DARK
    config:        S/C
    opmode:        DATA
    aperture:      NONE
    num_exp:       1
    time_per_exp:  20M
    priority:      1
    req_1:         RT ANALYSIS;
    comment_1:     ATTACH INSTR = BDUMPSTR

!

    linenum:       229.000
    targname:      NONE
    config:        COSTAR
    opmode:        DOB
    num_exp:       1
    time_per_exp:  30M
    priority:      1
    req_1:         REQ UPLINK;
    req_2:         AFTER 227 BY 24H;
    comment_1:     SET COSTAR DOB POSITION

!

    linenum:       230.000
    targname:      NONE
    config:        COSTAR
    opmode:        FOC
    num_exp:       1
    time_per_exp:  30M
    priority:      1
    req_1:         REQ UPLINK;
    req_2:         AFTER 229;
    comment_1:     SET COSTAR FOC TILTS

!
! end of exposure logsheet

! No scan data records found