!   $Id: 4707,v 4.1 1994/07/27 14:30:37 pepsa Exp $

coverpage:

  title_1:         WFPC-2 CALIBRATION SYSTEM FLAT FIELD CHECK
    proposal_for:  SME/WF2
    pi_fname:      AMIT
    pi_lname:      SEN
    pi_inst:       JPL
    pi_country:    USA
    pi_phone:      818-354-5933
    hours_par:     0.50
    wf_pc:         Y
! end of coverpage

abstract:

    line_1:        This activity takes exposures of the calibration system lamp.
    line_2:        Only the incandenscent (VIS) lamp will be used.  This is an
    line_3:        initial engineering check to monitor subsystem performance while
    line_4:        the lamp is being used.
    line_5:        This proposal implements Activity Summary WFII-03.

!
! end of abstract

general_form_proposers:

  lname:           SEN
    fname:         AMIT
    inst:          JPL
    country:       USA

!
! end of general_form_proposers block

general_form_text:

  question:        2
    section:       1
    line_1:        This is an early SMOV activity.

!

  question:        3
    section:       1
    line_1:        VIS Lamp Check:
    line_2:        Take VISFLAT exposures through the F555W, F439W and F814W
    line_3:        filters at specified exposure times.  Take two 60S DARKs
    line_4:        one before and one after the VISFLAT sequence.
    line_5:        This proposal implements Activity Summary WFII-03.

!

  question:        5
    section:       1
    line_1:        Prerequisites:  Proposal 4711.
    line_2:        UV Cal lamp system is expected to occur
    line_3:        later than deployment + 30 days to allow sufficient outgassing
    line_4:        time.  The UV Cal system shall not be used until approval of
    line_5:        WFPC2 PI, J. Trauger, has been received.  This is to avoid
    line_6:        polymerization of contaminants on either the UV source and/or
    line_7:        on the CCD detector windows. -- UVFLAT IS NOT USED IN THIS PROP.
    line_9:        WFPC2 in Conditional Operate Mode (Mech Pwr On, TECs off).
    line_11:       Engineering telemetry required during exposures; Include this
    line_12:       comment in the SMS Delivery Notice.
    line_14:       These exposures may be scheduled as generic parallels.
    line_16:       Schedule all exposures at the same temperature setpoint.

!
!end of general form text

general_form_address:

  lname:           SEN
    fname:         AMIT
    category:      PI
    inst:          JPL
    addr_1:        4800 OAK GROVE DRIVE
    addr_2:        MAIL STOP 179-104
    city:          PASADENA
    state:         CA
    zip:           91109
    country:       USA
    phone:         818-354-5933

!
! end of general_form_address records

! No fixed target records found

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       1.000
    targname:      DARK
    config:        WFPC2
    opmode:        IMAGE
    aperture:      WFALL
    sp_element:    DEF
    num_exp:       1
    time_per_exp:  60S
    priority:      1
    param_1:       ATD-GAIN=15
    req_1:         CYCLE 4/1-5;
    req_2:         SEQ 1-5 NO GAP;

!

    linenum:       2.000
    targname:      VISFLAT
    config:        WFPC2
    opmode:        IMAGE
    aperture:      WFALL
    sp_element:    F555W
    num_exp:       1
    time_per_exp:  2S
    priority:      1
    param_1:       ATD-GAIN=15
    comment_1:     MAKE SURE WE HAVE
    comment_2:     ENGINEERING TLM WHEN USING THE
    comment_3:     LAMPS FOR THE FIRST TIME. ANY
    comment_4:     NORMAL FORMAT IS OK.

!

    linenum:       3.000
    targname:      VISFLAT
    config:        WFPC2
    opmode:        IMAGE
    aperture:      WFALL
    sp_element:    F439W
    num_exp:       1
    time_per_exp:  60S
    priority:      1
    param_1:       ATD-GAIN=15
    comment_1:     MAKE SURE WE HAVE
    comment_2:     ENGINEERING TLM WHEN USING THE
    comment_3:     LAMPS FOR THE FIRST TIME. ANY
    comment_4:     NORMAL FORMAT IS OK.

!

    linenum:       4.000
    targname:      VISFLAT
    config:        WFPC2
    opmode:        IMAGE
    aperture:      WFALL
    sp_element:    F814W
    num_exp:       1
    time_per_exp:  0.8S
    priority:      1
    param_1:       ATD-GAIN=15
    comment_1:     MAKE SURE WE HAVE
    comment_2:     ENGINEERING TLM WHEN USING THE
    comment_3:     LAMPS FOR THE FIRST TIME. ANY
    comment_4:     NORMAL FORMAT IS OK.

!

    linenum:       5.000
    targname:      DARK
    config:        WFPC2
    opmode:        IMAGE
    aperture:      WFALL
    sp_element:    DEF
    num_exp:       1
    time_per_exp:  60S
    priority:      1
    param_1:       ATD-GAIN=15

!
! end of exposure logsheet

! No scan data records found