!  File:  4011C.PROP
!  Database:  PEPDB
!  Date:  20-FEB-1994:03:43:25

coverpage:

  title_1:         F/96 CAMERA,2ND,3RD STAGE FOCUS
    proposal_for:  CAL/FOC
    pi_fname:      MANFRED
    pi_lname:      MIEBACH
    pi_inst:       ST SCI
    pi_country:    USA
    foc:           X
! end of coverpage

abstract:

    line_1:        The purpose of this proposal is to verify the F/96 camera section,
    line_2:        second stage and third stage focus. Internal calibration sources are
    line_3:        used throughout this proposal. This proposal is intended to be run
    line_4:        every 12 months to monitor the detector focus

!
! end of abstract

general_form_proposers:

  lname:           MIEBACH
    fname:         MANFRED
    inst:          ST SCI
    country:       USA
    esa:           X

!
! end of general_form_proposers block

general_form_text:

  question:        3
    section:       1
    line_1:        Exposure line 1 of this proposal switches off the intensifier and
    line_2:        performs a series of 5 histograms to verify the VPU threshold setting. The
    line_3:        thresholds should be set just above the camera noise.
    line_4:        On return to full operate mode 5 more histograms are performed at various
    line_5:        focus coil current settings. The Green2 LED is used as an input.
    line_7:        Lines 11-18 perform a series of 8 histograms to verify the intensifier
    line_8:        second and third stage focus settings. The intensifier voltages and trimcoil
    line_9:        current are varied such that the two focii can be independently verified.
    line_11:       This proposal is intended to be run every 12 months to monitor the
    line_12:       detector focus

!
!end of general form text

general_form_address:

  lname:           MIEBACH
    fname:         MANFRED
    category:      PI
    inst:          STSCI/ESA
    addr_1:        3700 SAN MARTIN DR
    city:          BALTIMORE
    country:       USA

!
! end of general_form_address records

! No fixed target records found

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       1.000
    targname:      DARK
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  60M
    priority:      1
    req_1:         CYCLE 1 / 1-6;
    comment_1:     PERFORM A&V BLOCK XOV_THRESHOP FOR
    comment_2:     THE F/96 CHAIN.

!

    linenum:       2.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=64
    req_1:         SEQ 2-6 NO GAP;
    comment_1:     CHANGE FOCUS COIL CURRENT VIA
    comment_2:     XPDAELB TO COMMAND SETTING 9
    comment_3:     WITH FINE FOCUS BIT SET TO 1

!

    linenum:       3.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=64
    comment_1:     CHANGE FOCUS COIL CURRENT VIA
    comment_2:     XPDAELB TO COMMAND SETTING 10
    comment_3:     WITH FINE FOCUS BIT SET TO 0

!

    linenum:       4.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=64
    comment_1:     CHANGE FOCUS COIL CURRENT VIA
    comment_2:     XPDAELB TO COMMAND SETTING 11
    comment_3:     WITH FINE FOCUS BIT SET TO 0

!

    linenum:       5.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=64
    comment_1:     CHANGE FOCUS COIL CURRENT VIA
    comment_2:     XPDAELB TO COMMAND SETTING 11
    comment_3:     WITH FINE FOCUS BIT SET TO 1

!

    linenum:       6.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       2
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=64
    comment_1:     RETURN FOCUS COIL CURRENT TO NOMINAL
    comment_2:     VIA XPDAELB WITH COMMAND SETTING 10
    comment_3:     WITH FINE FOCUS BIT SET TO 1

!

    linenum:       11.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    req_1:         SEQ 11-18 NO GAP;
    req_2:         CYCLE 1 / 11-18;
    comment_1:     CHANGE TRIMCOIL COIL CURRENT
    comment_2:     VIA XPDAELB TO 0.0 MA

!

    linenum:       12.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     CHANGE TRIMCOIL COIL CURRENT
    comment_2:     VIA XPDAELB TO 102.048 MA

!

    linenum:       13.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     CHANGE TRIMCOIL COIL CURRENT
    comment_2:     VIA XPDAELB TO 204.095

!

    linenum:       14.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     CHANGE TRIMCOIL COIL CURRENT
    comment_2:     VIA XPDAELB TO 306.142 MA

!

    linenum:       15.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     CHANGE TRIMCOIL COIL CURRENT
    comment_2:     VIA XPDAELB TO 405.0 MA

!

    linenum:       16.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     VIA XPDAELB CHANGE TRIMCOIL
    comment_2:     COIL CURRENT TO 95.67 MA AND
    comment_3:     IEHT12 TO 10.85 KV.

!

    linenum:       17.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       1
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     VIA XPDAELB CHANGE TRIMCOIL
    comment_2:     COIL CURRENT TO 197.717 MA AND
    comment_3:     IEHT12 TO 11.66 KV.

!

    linenum:       18.000
    targname:      INTFLAT
    config:        FOC/96
    opmode:        HIST
    aperture:      512X512
    num_exp:       2
    time_per_exp:  12M
    priority:      1
    param_1:       LED=GREEN-2,
    param_2:       LED-STEP=16
    comment_1:     VIA XPDAELB RETURN TO NOMINAL
    comment_2:     FOCUS BY CHANGING TRIMCOIL
    comment_3:     COIL CURRENT TO 146.70 MA AND
    comment_4:     IEHT12 TO 11.26 KV.

!
! end of exposure logsheet

! No scan data records found