!  File:  2751C.PROP
!  Database:  PEPDB
!  Date:  17-FEB-1994:11:02:39

coverpage:

  title_1:         INITIAL WF/PC DE-FILTH LOW-TEMP TEST
    proposal_for:  OV/WFC
    pi_fname:      JAMES
    pi_mi:         A.
    pi_lname:      WESTPHAL
    pi_inst:       CALTECH
    pi_country:    USA
! end of coverpage

abstract:

    line_1:        This engineering test warms the optical bench and
    line_2:        CCDs of the WF/PC and drives off possible contamination.
    line_3:        A UV calibration will be preformed to determine the
    line_4:        quantum efficency of the detectors.  This test should
    line_5:        be coupled to each science observation that plans to do
    line_6:        photometric measurements with filters F122N, F157W,
    line_7:        F194W, or G200L.

!
! end of abstract

general_form_proposers:

  lname:           DANIELSON
    fname:         G.
    mi:            E.
    inst:          CALTECH
    country:       USA

!

  lname:           WESTPHAL
    fname:         JAMES
    mi:            A.
    inst:          CALTECH
    country:       USA

!

  lname:           GUNN
    fname:         JAMES
    mi:            E.
    inst:          PRINCETON UNIVERSITY
    country:       USA

!
! end of general_form_proposers block

general_form_text:

  question:        2
    section:       0
    line_1:        This test sequence establishes a WF/PC system baseline and
    line_2:        monitors the camera performance in the UV at the beginning
    line_3:        and at the end of the test.  This should drive the UV
    line_4:        contaminates from the CCDs.

!

  question:        3
    section:       0
    line_1:        A WF system baseline is established through a multi-step
    line_2:        sequence:  1) UV baseline calibration; 2) Turning TEC pwr
    line_3:        off (for WF & PC); 3) CCD heaters are turned on; 4) Wait
    line_4:        for eight hours
    line_5:        set for a temperature of -82 degrees C.
    line_9:        If the TEC's will remain off (Day 22):
    line_10:       - CJ temps must be < -40 C to continue
    line_11:       If the TEC's will be turned on (Day 46):
    line_12:       - HJ teps must be < -20 C before turning TEC's on
    line_13:       - CJ temps must be < -80 C to continue (after TEC turn-on)
    line_14:       - Repeat UV Calibration measurements after detectors
    line_15:       reach -80 C and again after the UV observation.

!

  question:        5
    section:       0
    line_1:        Real-time contact is not required.
    line_3:        SI C&DH operational format AN.

!
!end of general form text

general_form_address:

  lname:           DANIELSON
    fname:         G.
    mi:            E.
    category:      CON
    inst:          CALTECH
    addr_1:        DIVISION OF GEOLOGICAL & PLANETARY SCIENCES
    city:          PASADENA
    state:         CA
    zip:           91125
    country:       USA
    phone:         (818) 356-6861

!

  lname:           WESTPHAL
    fname:         JAMES
    mi:            A.
    category:      PI
    inst:          CALTECH
    addr_1:        DIVISION OF GEOLOGICAL & PLANETARY SCIENCE
    city:          PASADENA
    state:         CA
    zip:           91125
    country:       USA
    phone:         (818) 356-4900

!

  lname:           GUNN
    fname:         JAMES
    mi:            E.
    category:      CON
    inst:          PRINCETON UNIVERISITY
    addr_1:        ASTROPHYSICAL SCIENCE
    addr_2:        PEYTON HALL
    city:          PRINCETON
    state:         NJ
    zip:           08540
    country:       USA
    phone:         (609) 452-3802

!
! end of general_form_address records

fixed_targets:

    targnum:       1
    name_1:        A+81266
    descr_1:       UV SPECTROPHOTOMETRIC STANDARD
    pos_1:         RA= 09H21M29S +/-1S,
    pos_2:         DEC= 81D43'00" +/-10",
    equinox:       2000
    fluxnum_1:     1
    fluxval_1:     V=12.1 +/-0.5

!
! end of fixed targets

! No solar system records found

! No generic target records found

exposure_logsheet:

    linenum:       10.000
    sequence_1:    USE
    sequence_2:    UVBASELINE
    req_1:         SEQ 10-30 NO GAP;

!

    linenum:       20.000
    targname:      DARK
    config:        S/C
    opmode:        POINTING
    aperture:      V1
    num_exp:       1
    time_per_exp:  1M
    priority:      1
    param_1:       CONTROL=GYRO,
    comment_1:     TECS OFF.  M1 MIRROR HEATER ON.  CCD
    comment_2:     HEATERS ON.  (SI=LTDECON,
    comment_3:     PYRAMID=HOLD). NOTE TRANSITION TIME
    comment_4:     TO LTDECON IS 8HR, PROVIDING THE TIME
    comment_5:     NEEDED FOR THE LOW TEMP BAKEOUT.

!

    linenum:       30.000
    sequence_1:    USE
    sequence_2:    UVBASELINE

!

    linenum:       110.000
    sequence_1:    DEFINE
    sequence_2:    UVBASELINE
    targname:      A+81266
    config:        WFC
    opmode:        IMAGE
    aperture:      W1
    sp_element:    G200L
    num_exp:       1
    time_per_exp:  5S
    priority:      1
    req_1:         SEQ 110-180 NO GAP;
    req_2:         SEQ 110-140 NON-INT;
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       120.000
    sequence_1:    ^
    targname:      ^
    config:        ^
    opmode:        ^
    aperture:      W2
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  ^
    priority:      ^
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       130.000
    sequence_1:    ^
    targname:      ^
    config:        ^
    opmode:        ^
    aperture:      W3
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  ^
    priority:      ^
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       140.000
    sequence_1:    ^
    targname:      ^
    config:        ^
    opmode:        ^
    aperture:      W4
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  ^
    priority:      ^
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       150.000
    sequence_1:    ^
    targname:      ^
    config:        PC
    opmode:        ^
    aperture:      P5
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  25S
    priority:      ^
    req_1:         SEQ 150-180 NON-INT;
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       160.000
    sequence_1:    ^
    targname:      ^
    config:        ^
    opmode:        ^
    aperture:      P6
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  ^
    priority:      ^
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       170.000
    sequence_1:    ^
    targname:      ^
    config:        ^
    opmode:        ^
    aperture:      P7
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  ^
    priority:      ^
    comment_1:     ONLY READOUT 1 CCD.

!

    linenum:       180.000
    sequence_1:    ^
    targname:      ^
    config:        ^
    opmode:        ^
    aperture:      P8
    sp_element:    ^
    num_exp:       ^
    time_per_exp:  ^
    priority:      ^
    comment_1:     ONLY READOUT 1 CCD.

!
! end of exposure logsheet

! No scan data records found